Zircon StudSensor Pro LCD Deep-Scanning Stud Finder Instruction Manual

Уводзіны

The Zircon StudSensor Pro LCD is an electronic stud finder designed to quickly and easily locate the edges of wood and metal studs and joists behind walls, floors, and ceilings. It features an easy-to-read display, the patented SpotLite Pointing System, and Wire Warning detection for live AC-Voltage.

Інфармацыя па бяспецы

• Always exercise caution when scanning walls, ceilings, and floors that may contain electrical wiring or plumbing.
• The Wire Warning detection indicates the presence of live, unshielded electrical wiring. Shielded wires may not be detected.
• Do not rely solely on the stud finder to avoid hazards. Always turn off power to circuits before cutting or drilling into walls.
• Гэты інструмент прызначаны толькі для ўнутранага выкарыстання.

Змест пакета

• Zircon StudSensor Pro LCD Tool
• Інструкцыя па эксплуатацыі (гэты дакумент)
• How-to Z-Card

Асаблівасці прадукту

• Stud Scan Mode: Locates edges of wood or metal studs up to 3/4 inch (19 mm) deep.
• DeepScan Mode: Doubles scanning depth to 1-1/2 inches (38 mm) for thicker walls.
• Лёгкі для чытання ВК-дысплей: Clearly indicates stud edges and other information.
• Patented SpotLite Pointing System: Shines a beam of light on the wall to identify the target.
• Audio Tone: Provides audible alerts when a stud edge is reached.
• Выяўленне папярэджання пра правады: Indicates the presence of live, unshielded electrical wiring up to 2 inches (51 mm) deep.
• "Over-the-Stud" Indicator: Alerts the user if scanning begins over a stud, prompting a new starting location.
• TruCal Technology: Calibrates to any wall's density, with an icon indicating readiness.

Малюнак 1: Фронт view of the Zircon StudSensor Pro LCD, showing the display, mode switch, and the SpotLite beam.

Настройка

1. Устаноўка батарэі

1. Адкрыйце крышку батарэйнага адсека, размешчаную на задняй панэлі прылады.
2. Insert a new 9V alkaline battery, ensuring correct polarity (+/-).
3. Надзейна зачыніце крышку батарэйнага адсека.

2. Power On and Calibration

1. Place the tool flat against the wall where you intend to scan. Ensure it is not over a stud or dense material.
2. Press and hold the Power Button. The unit will emit a short beep, and the TruCal icon will appear on the LCD, indicating calibration.
3. Keep the tool flat against the wall and still until the TruCal icon disappears and the unit beeps again, signaling successful calibration.
4. If the "over-the-stud" indicator appears, release the Power Button, move the tool to a different location, and recalibrate.

Інструкцыя па эксплуатацыі

1. Selecting a Scan Mode

Use the slide switch on the front of the tool to select either Stud Scan or DeepScan рэжым.

Малюнак 2: Збоку view of the Zircon StudSensor Pro LCD, highlighting the mode selection switch.

2. Scanning for Studs

1. After calibration, keep the Power Button pressed and slowly slide the tool horizontally across the wall surface.
2. As the tool approaches a stud, the LCD display will show increasing bars, indicating proximity.
3. When the tool detects the edge of a stud, the SpotLite Pointing System will illuminate, an audio tone will sound, and the "EDGE" indicator will appear on the LCD. Mark this spot.
4. Continue sliding past the stud until the indicators turn off. Then, slide back from the opposite direction to locate the other edge of the stud. Mark this second spot.
5. The center of the stud is typically between these two marked edges.

Малюнак 3: A user operating the Zircon StudSensor Pro LCD on a wall to locate studs.

3. Wire Warning Detection

The Wire Warning detection icon will appear on the LCD and an audible alert will sound if live, unshielded AC electrical wiring is detected within approximately 2 inches (51 mm) of the wall surface. This feature is active in both Stud Scan and DeepScan modes.

Папярэджанне: Always turn off power to circuits before drilling or cutting into walls.

Тэхнічнае абслугоўванне

• Keep the tool clean and dry. Wipe with a soft, damp cloth if necessary. Do not use abrasive cleaners or solvents.
• Remove the battery if the tool will not be used for an extended period to prevent leakage.
• Захоўвайце інструмент у прахалодным, сухім месцы, удалечыні ад прамых сонечных прамянёў і экстрэмальных тэмператур.

Ліквідацыю непаладак

Тэхнічныя характарыстыкі

• мадэль: SS Pro LCD
• Stud Scan Depth: Да 3/4 цалі (19 мм)
• DeepScan Depth: Up to 1-1/2 inches (38 mm)
•  style="color:#333333;">Wire Warning Detection Depth: Up to 2 inches (51 mm) for live, unshielded AC wires
• Крыніца харчавання: 9V alkaline battery (not included)
• Працоўная тэмпература: Ад 20°F да 120°F (ад -7°C да 49°C)
• Тэмпература захоўвання: Ад -20°F да 150°F (ад -29°C да 66°C)
• Памеры: Прыкладна 6 х 12 х 4 цалі (15.2 х 30.5 х 10.2 см)
• Вага: Approximately 9.6 ounces (272 grams) without battery
• матэрыял: Пластыкавыя
• колер: Жоўты

Гарантыя і падтрымка

Абмежаваная гарантыя

Zircon Corporation warrants this product to be free from defects in materials and workmanship for адзін год from the date of purchase. This warranty does not cover damage due to misuse, abuse, or normal wear and tear.

Падтрымка кліентаў

For technical assistance or warranty claims, please visit the official Zircon webсайт або звярніцеся ў іх аддзел абслугоўвання кліентаў.

Visit Zircon's Official Webсайт