Cornat Tratto TR182 Two-Handle Basin Інструкцыя па эксплуатацыі змяшальніка

1. Уводзіны

This manual provides detailed instructions for the installation, operation, and maintenance of your Cornat Tratto TR182 Two-Handle Basin Mixer Tap. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product. Retain this manual for future reference.

Малюнак 1: The Cornat Tratto TR182 Two-Handle Basin Mixer Tap. This image displays the chrome-plated tap with its high, swivelling spout and two cross-handle controls for hot and cold water.

2. Інфармацыя па бяспецы

• Заўсёды адключайце асноўную падачу вады перад пачаткам любых мантажных або рамонтных работ.
• Пераканайцеся, што ўсе злучэнні надзейныя, каб пазбегнуць уцечак.
• Калі вы не ўпэўненыя ў якім-небудзь этапе працэсу ўстаноўкі, звярніцеся да кваліфікаванага сантэхніка.
• Do not use abrasive cleaners or harsh chemicals on the chrome-plated surface, as this can damage the finish.
• This tap is designed for high-pressure water systems. Ensure your water system is compatible.

3. Змесціва ўпакоўкі

Please check that all components are present before starting installation:

• 1 x Cornat Tratto TR182 Basin Змяшальнік Націсніце
• 1 x Connection Hose Set (350 mm length)
• 1 x Pull Drain Fitting (1 1/4 inch)
• Mounting Accessories (washers, nuts, etc.)

4. Тэхнічныя характарыстыкі

Малюнак 2: Diagram illustrating the dimensions of the Cornat Tratto TR182 tap, including total height (250mm), spout reach (137mm), and base diameter (55mm).

5. Усталёўка (налада)

5.1 Неабходныя інструменты (не ўключаны)

• Развадны ключ
• Адвёртка
• Стужка сантэхніка (стужка з ПТФЭ)
• Basin гаечны ключ (неабавязкова, для цяжкадаступных месцаў)
• Bucket and towels (for spills)

5.2 Этапы перад устаноўкай

1. Адключыць падачу вады: Locate the main water shut-off valve for your home or the shut-off valves under the sink. Turn them off completely.
2. Drain Existing Water: Open the existing tap to drain any remaining water from the lines.
3. Remove Old Tap: Disconnect the water supply lines from the old tap and remove the mounting nuts. Carefully lift out the old tap and drain fitting.
4. Чыстая мантажная паверхня: Clean the sink or countertop surface where the new tap will be installed.

5.3 Tap Installation

1. Attach Connection Hoses: Screw the 350mm connection hoses into the base of the new tap. Hand-tighten first, then use a wrench for a snug fit, but do not overtighten.
2. Position Tap: Place the tap through the single mounting hole on your basin or countertop. Ensure any rubber gaskets or seals are correctly positioned between the tap base and the sink surface.
3. Secure Tap: From underneath the sink, slide the rubber washer, metal washer, and mounting nut onto the threaded rod(s) of the tap. Tighten the mounting nut securely to hold the tap in place.
4. Падключэнне водазабеспячэння: Connect the hot and cold water supply lines to the corresponding shut-off valves. Use plumber's tape on the threads for a watertight seal. Tighten with a wrench.

5.4 Устаноўка дрэнажнай арматуры

1. Збярыце каналізацыю: Follow the instructions provided with the pull drain fitting (1 1/4 inch) to assemble it. Ensure all seals are correctly placed.
2. Усталяваць дрэнаж: Insert the drain fitting into the drain hole of the basin. From underneath, secure it with the provided nut and washer, ensuring a watertight seal.
3. Connect Pull Rod: Connect the pull rod from the tap to the drain stopper mechanism. Adjust the rod to ensure the stopper opens and closes smoothly.
4. Падключэнне да P-Trap: Connect the drain fitting to your existing P-trap assembly.

5.5 Праверкі пасля ўстаноўкі

1. Аднаўленне водазабеспячэння: Павольна ўключыце асноўную падачу вады.
2. Праверце ўцечкі: Carefully inspect all connections under the sink for any signs of leaks. Tighten connections if necessary.
3. Прамыўныя лініі: Open both hot and cold handles on the tap to flush out any debris from the water lines. Let the water run for a few minutes.

6. Аперацыя

The Cornat Tratto TR182 features two cross-handles for precise control of water flow and temperature.

• Халодная вада: Turn the right handle counter-clockwise to open the cold water supply. Turn clockwise to close.
• Гарачая вада: Turn the left handle counter-clockwise to open the hot water supply. Turn clockwise to close.
• Кантроль тэмпературы: Adjust the hot and cold handles simultaneously to achieve the desired water temperature.
• Паваротны носік: The high spout can be swiveled to direct the water flow as needed.
• Заглушка для зліву: Use the pull rod located behind the tap to open and close the basin's drain stopper. Pull up to close the drain, push down to open.

7. Тэхнічнае абслугоўванне

7.1 Cleaning the Tap

• Clean the chrome-plated surface regularly with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for chrome.
• Старанна прамыйце чыстай вадой і высушыце мяккай тканінай, каб пазбегнуць плям ад вады.
• Avoid using abrasive sponges, scouring pads, or harsh chemical cleaners (e.g., bleach, ammonia-based products) as these can damage the finish.

7.2 Тэхнічнае абслугоўванне аэратара

The tap features a low-noise aerator (M24 x 1) designed to provide a soft, water-saving jet. Over time, mineral deposits can accumulate in the aerator, reducing water flow.

1. Зняць аэратар: Unscrew the aerator from the end of the spout. You may need an aerator key or a coin.
2. Чысты: Rinse the aerator components under running water. Use a soft brush to remove any debris or mineral deposits. For stubborn deposits, soak the aerator in a solution of equal parts white vinegar and water for 30 minutes.
3. Зборка: Screw the clean aerator back into the spout, ensuring it is hand-tightened.

7.3 Замена картрыджа

The tap is equipped with easily replaceable cartridges featuring low-wear ceramic sealing discs. If you experience persistent dripping or difficulty controlling water flow, a cartridge may need replacement.

1. Адключыць падачу вады: Shut off the hot and cold water supply to the tap.
2. Выдаліць маркер: Carefully pry off the decorative cap on the handle (if present) and unscrew the handle screw. Remove the handle.
3. Доступ да картрыджа: Unscrew the retaining nut or ring that holds the cartridge in place.
4. Замяніць картрыдж: Carefully lift out the old cartridge and insert a new, identical replacement cartridge.
5. Зборка: Reattach the retaining nut/ring and the handle. Turn on the water supply and check for leaks.

8. Выпраўленне непаладак

9. Гарантыя і падтрымка

For specific warranty information, please refer to the documentation provided at the time of purchase or contact Cornat customer support.

If you encounter issues that cannot be resolved using the troubleshooting guide, please contact your retailer or a qualified plumbing professional.

Малюнак 3: The official Cornat brand logo.