Watts FFSS12-R Corrugated Stainless Water Heater Connector Instruction Manual

Уводзіны

This manual provides essential instructions for the safe and proper installation, operation, and maintenance of your Watts FFSS12-R 12-Inch by 3/4-Inch FIP Corrugated Stainless Water Heater Connector. Please read this manual thoroughly before beginning installation to ensure correct usage and to prevent potential damage or injury.

The Watts FFSS12-R is designed to connect electric or gas water heaters to the water supply. Its corrugated stainless steel construction offers flexibility and high flow, while the built-in dielectric sleeve helps prevent galvanic corrosion between dissimilar metals.

Важная інфармацыя па бяспецы

• ПАПЯРЭДЖАННЕ: Installation should be performed by a qualified professional or a knowledgeable individual familiar with plumbing systems and local codes.
• Always shut off the main water supply and drain the water heater before beginning any work.
• Пераканайцеся, што ўсе злучэнні шчыльныя, каб пазбегнуць уцечак. Не перацягвайце.
• Карыстайцеся адпаведнымі сродкамі індывідуальнай абароны (СІЗ), такімі як пальчаткі і ахоўныя акуляры.
• Выконвайце ўсе мясцовыя сантэхнічныя і будаўнічыя нормы.
• This product is designed for water heater connections only. Do not use for other applications.

Змест пакета

Перад пачаткам усталёўкі пераканайцеся, што ўсе кампаненты наяўныя:

• 1 x Watts FFSS12-R 12-Inch by 3/4-Inch FIP Corrugated Stainless Water Heater Connector

Інструкцыя па ўстаноўцы

Для правільнай усталёўкі ўважліва выканайце наступныя дзеянні:

1. Падрыхтуйце воданагравальнік:
   • Turn off the water supply to the water heater at the main shut-off valve.
   • Turn off the power supply (electricity or gas) to the water heater.
   • Drain the water heater completely. Refer to your water heater's manual for specific draining instructions.
2. Remove Old Connectors (if applicable):
   • Carefully disconnect and remove any existing water heater connectors. Be prepared for residual water.
3. Inspect the Watts FFSS12-R Connector:

   Examine the connector for any signs of damage or manufacturing defects before installation.

   

   Image: Watts FFSS12-R 12-Inch by 3/4-Inch FIP Corrugated Stainless Water Heater Connector. This image shows the flexible corrugated stainless steel hose with threaded FIP connections at both ends, ready for installation.

4. Connect to Water Heater:
   • Apply a suitable thread sealant (e.g., PTFE tape or pipe dope) to the male threads of the water heater's inlet and outlet ports.
   • Hand-tighten one end of the Watts FFSS12-R connector to the water heater's cold water inlet (typically marked blue or 'C').
   • Hand-tighten the other Watts FFSS12-R connector (or the other end of the same connector if only one is used for both hot/cold, though typically two are used) to the water heater's hot water outlet (typically marked red or 'H').
   • Using a wrench, tighten each connection an additional 1/2 to 1 full turn past hand-tight. Do not overtighten, as this can damage the threads or the connector.
5. Падключэнне да хатняй сантэхнікі:
   • Apply thread sealant to the male threads of the house's cold and hot water supply lines.
   • Connect the remaining ends of the Watts FFSS12-R connectors to the corresponding cold and hot water supply lines.
   • Hand-tighten, then use a wrench to tighten an additional 1/2 to 1 full turn.
6. Праверце ўцечкі:
   • Павольна ўключыце асноўную падачу вады.
   • Open a hot water faucet in your home to allow air to escape from the water heater and pipes. Once water flows steadily, close the faucet.
   • Carefully inspect all connections for leaks. If a leak is detected, turn off the water supply, drain the system slightly, and re-tighten the leaking connection. Do not overtighten.
7. Аднавіць сілу:
   • Once all connections are secure and leak-free, restore power (electricity or gas) to the water heater.
   • Allow the water heater to fill and heat up according to its manufacturer's instructions.

Аперацыя

The Watts FFSS12-R connector is a passive component designed to provide a flexible and secure connection between your water heater and the plumbing system. Once installed correctly, it operates continuously without user intervention. Its corrugated design allows for slight movement and vibration without compromising the seal, while the built-in dielectric sleeve helps prevent galvanic corrosion between dissimilar metals.

Тэхнічнае абслугоўванне

Regular maintenance is minimal for this product, but periodic inspection is recommended:

• Штогадовая праверка: Annually, visually inspect the connectors for any signs of corrosion, leaks, kinks, or damage.
• Праверка герметычнасці: If any signs of moisture or dripping are observed, immediately shut off the water supply and investigate the source of the leak. Re-tighten connections if necessary, but do not overtighten.
• Уборка: Clean the exterior of the connector with a soft, damp анучай пры неабходнасці. Не выкарыстоўвайце агрэсіўныя хімікаты або абразіўныя ачышчальнікі.

Ліквідацыю непаладак

If you encounter issues not listed here or cannot resolve a problem, contact a qualified plumbing professional.

Тэхнічныя характарыстыкі

• мадэль: FFSS12-R
• Даўжыня: 12 цаляў
• Памер злучэння: 3/4-inch FIP (Female Iron Pipe)
• матэрыял: Corrugated Stainless Steel
• Максімальны ціск: 125 PSI
• Убудаваныя функцыі: Dielectric sleeve, threaded swivel adapters
• Памеры (Д х Ш х У): 12 х 0.75 х 0.75 цалі
• Вага прадмета: 4.8 унцыі

Гарантыя і падтрымка

For specific warranty information, please refer to the documentation provided with your purchase or visit the official Watts website. For technical support or inquiries, please contact Watts customer service directly.

Watts Official Webсайт: www.watts.com