Intermatic EI200LA Electronic In-Wall Countdown Auto-Off Timer User Manual

Уводзіны

The Intermatic EI200LA Electronic In-Wall Countdown Auto-Off Timer is designed to replace standard toggle-style wall switches, providing silent electronic timing operation. This timer offers time ranges of 5, 10, 15, and 30 minutes, making it suitable for various applications such as indoor/outdoor lighting, exhaust fans, and other electrical loads. This manual provides essential information for safe installation, operation, and maintenance of your timer.

Асаблівасці

• Provides 5/10/15/30 Minute time ranges.
• Available in Light Almond finish.
• Offers silent operation.
• Replaces single-pole switches in a variety of applications.
• CFL compatible with all EI200 series timers (EI210W, EI220W, etc.), EI500C, EI500WC, EI500LAC, EI600C and EI600LAC.
• Designed for use with a decorator-style wall plate (NOT included).

Электрычныя рэйтынгі

• 120 В пераменнага току, 60 Гц
• 15A General Purpose
• Вальфрам 1000 Вт
• Матор 1/4 HP
• Баласт 1000 ВА

Інструкцыя па ўстаноўцы

ПАПЯРЭДЖАННЕ: Каб пазбегнуць пажару, удару токам або смерці, адключыце сілкаванне на аўтаматычным выключальніку і праверце, што сілкаванне адключана перад падключэннем.

Lead Wire Identification:

• чорны: Лінія/Гарачае
• Белы: Нейтральны
• Чырвоны: Нагрузка
• Зялёны: зямля

1. Remove wall plate and disconnect light switch. Make sure both "hot" and neutral wires are present in the junction box. (See Fig. 1). If both wires are not present, additional wiring may be necessary before installation can be completed.
2. Connect red timer wire to wire from fixture using wire connector. Connect black timer wire to the "hot" (usually black or red) wire in junction box using wire connector. Cut white wire in junction box (or green splice) and strip 3/8" of insulation on both wires. Connect white timer wire to white wire in junction box using wire connector. (See Fig. 2).
3. If the wall switch you are replacing had separate grounding conductors connected to the GREEN screw on the switch, make sure to connect these to the green wire from the timer with a wire connector.
4. Праверце надзейнасць злучэння ўсіх правадоў.
5. Place all wires inside junction box. Fit timer into junction box. Next, install timer using (2) mounting screws furnished.
6. Reconnect your electrical power.

Figure 1 & 2: Wiring diagrams for the EI200LA timer. Figure 1 illustrates the timer's internal connections, while Figure 2 shows the typical wiring setup within a wall box, connecting the timer to the fixture and power supply.

Аперацыя

Рэжым таймера

To enter Timer mode, press and release the push button (for less than 2 seconds) repeatedly to select one of the four time settings: OFF (5 minutes - 10 minutes - 15 minutes - 30 minutes) - OFF. The illuminated LED indicates which time setting is selected and the connected load is turned ON. Timer starts counting down until time out is reached, all 5 LED's go off and the connected load turns OFF.

Рэжым утрымання (бесперапынная праца)

To turn timer ON for extended periods of time, press and hold the push button for more than 2 seconds. Timer enters HOLD mode, HOLD LED turns on, and the connected load is turned ON. To exit HOLD mode press and release the push button, all 5 LED's go off and the connected load turns OFF.

Image of the Intermatic EI200LA timer face, showing the push button and LED indicators for 5, 10, 15, 30 minutes, and HOLD mode.

Тэхнічнае абслугоўванне

The Intermatic EI200LA timer is designed for maintenance-free operation. To ensure longevity and proper function, keep the device clean and free from dust. Do not use abrasive cleaners or solvents. If the device requires cleaning, gently wipe the surface with a soft, damp cloth. Ensure power is disconnected at the circuit breaker before any cleaning or inspection.

Ліквідацыю непаладак

• Таймер не адказвае: Ensure power is supplied to the circuit. Check the circuit breaker. Verify all wiring connections are secure according to the installation instructions.
• Load not turning ON/OFF: Confirm the timer is correctly wired to the load. Check the selected time setting or if the timer is in HOLD mode.
• Перарывістая праца: Inspect wiring for loose connections. Ensure the timer is not overloaded beyond its specified electrical ratings.

If issues persist after following these steps, contact a qualified electrician or Intermatic customer support for assistance.

Тэхнічныя характарыстыкі

Інфармацыя аб гарантыі

This Intermatic product is covered by a Гарантыя 1 год. This warranty covers replacement of the unit but does not include labor costs. For detailed warranty terms and conditions, please refer to the official Intermatic warranty statement or contact customer support.

Падтрымка кліентаў

For technical assistance, troubleshooting, or warranty claims, please contact Intermatic customer support. You can find contact information on the official Intermatic website or by referring to the product packaging.