DeFelsko PosiTector 6000 F1 Coating Thickness Gauge User Manual

1. Уводзіны

This manual provides comprehensive instructions for the safe and effective operation of your DeFelsko PosiTector 6000 F1 Coating Thickness Gauge. This instrument is designed for accurate measurement of coating thickness on ferrous metal substrates. Please read this manual thoroughly before using the device to ensure proper handling and to maximize its lifespan.

2. Інфармацыя па бяспецы

Always observe the following safety precautions to prevent injury or damage to the instrument:

• Do not expose the gauge to extreme temperatures, humidity, or corrosive environments.
• Avoid dropping the instrument or subjecting it to severe impact.
• Do not attempt to disassemble or repair the gauge yourself. Refer all servicing to qualified personnel.
• Keep the probe tip clean and free from debris to ensure accurate readings.
• Use only the specified battery type (AAA) and ensure correct polarity during installation.

3. Змесціва ўпакоўкі

Verify that all items listed below are present in your DeFelsko PosiTector 6000 F1 package:

• DeFelsko PosiTector 6000 F1 Coating Thickness Gauge with Built-in Probe
• Сумка для пераноскі
• Precision Plastic Shims
• Protective Lens Shield
• Protective Rubber Holster
• Папружка
• Батарэйкі тыпу AAA (3 у камплекце)
• NIST Calibration Certificate

4. Прадукт скончыўсяview

The DeFelsko PosiTector 6000 F1 is a robust and accurate instrument designed for measuring coating thickness. Below are key components of the gauge:

Малюнак 4.1: Спераду view of the DeFelsko PosiTector 6000 F1 showing the display, control buttons, and integrated probe.

• Дысплей: Digital screen showing measurement readings, units, and menu options.
• Кнопкі кіравання: Used for navigation, calibration, and setting adjustments.
• Integrated Probe: The sensor at the bottom of the unit used to contact the coated surface for measurement.
• Батарэйны адсек: Located at the rear, for AAA batteries.

5. Настройка

5.1 Устаноўка батарэі

1. Locate the battery compartment cover on the back of the gauge.
2. Адкрыйце крышку.
3. Insert three (3) AAA batteries, ensuring correct polarity as indicated inside the compartment.
4. Надзейна зачыніце крышку батарэйнага адсека.

5.2 Першапачатковае ўключэнне

Press the power button (usually the center button) to turn on the gauge. The display will illuminate and show the current measurement mode.

5.3 Attaching Wrist Strap and Holster

For added security and protection, attach the included wrist strap to the designated loop on the gauge and place the gauge into the protective rubber holster.

6. Інструкцыя па эксплуатацыі

6.1 Асноўныя вымярэнні

1. Пераканайцеся, што манометр уключаны.
2. Place the probe flat on the coated surface to be measured. Ensure full contact.
3. The reading will appear instantly on the display.
4. Lift the probe from the surface to take another measurement.

Figure 6.1: The PosiTector 6000 F1 being used to measure coating thickness on a metal I-beam.

Figure 6.2: The PosiTector 6000 F1 being used to measure coating thickness on a curved pipe surface.

6.2 Каліброўка

Regular calibration ensures the accuracy of your gauge. Refer to the detailed calibration procedure in the full PosiTector 6000 manual for specific steps using the included precision plastic shims and uncoated ferrous metal substrate.

6.3 Выбар блока

The PosiTector 6000 F1 can display measurements in mils (thou) or micrometers (um). Consult the gauge's menu system (typically accessed via the center button) to switch between these units as needed.

7. Тэхнічнае абслугоўванне

7.1 Ачыстка

• Wipe the gauge body with a soft, dry cloth.
• For the probe tip, use a soft cloth lightly dampened with isopropyl alcohol if necessary. Ensure no liquid enters the gauge.
• Не выкарыстоўвайце абразіўныя ачышчальнікі або растваральнікі.

7.2 Захоўванне

When not in use, store the PosiTector 6000 F1 in its protective carrying case in a dry, temperature-controlled environment. Remove batteries if storing for extended periods to prevent leakage.

8. Выпраўленне непаладак

If the problem persists after attempting these solutions, please contact DeFelsko customer support.

9. Тэхнічныя характарыстыкі

• Maximum Thickness Measured: 60 mil (1500 um)
• Minimum Thickness Measured: 0 мільёнаў
• Thickness Measurement Accuracy: +(0.05 mil + 1 Percent) Up to 2 mil; +(0.1 mil + 1 Percent) greater than 2 mils
• Calibration Certificate Type: NIST
• Тып дысплея: Лічбавы
• Number of Records Stored: 1,000
• Метад тэставання: Магнітныя
• Сумяшчальны матэрыял: Чорны метал
• Крыніца харчавання: 3 батарэйкі AAA (у камплекце)
• Памеры прадукту: 9 х 5 х 3 цалі
• Вага прадмета: 1 фунт
• Нумар мадэлі: F1
• ASIN: B0052P4B7G
• вытворца: Defelsko

10. Гарантыя і падтрымка

DeFelsko products are known for their quality and reliability. For detailed warranty information and technical support, please refer to the official DeFelsko website or contact their customer service department directly. Keep your purchase receipt and the NIST Calibration Certificate for warranty claims.

Кантактная інфармацыя: Калі ласка, наведайце www.defelsko.com каб атрымаць найноўшыя рэсурсы падтрымкі і кантактную інфармацыю.