1. Прадукт скончыўсяview
The DuraPro 102619 Lead-Free Lavatory Connector is designed for reliable water supply connections in kitchen and bathroom applications. This connector features durable construction and is engineered for ease of installation and long-term performance.
Image 1.1: DuraPro 102619 Lead-Free Lavatory Connector. This image shows the braided stainless steel hose with connection fittings on both ends.
Асноўныя характарыстыкі:
- NSF-approved high temperature-reinforced inner liner for safety and durability.
- 304 stainless steel braided jacket provides strength and corrosion resistance.
- Rated for 2,400 psi burst pressure at 70° F, ensuring robust performance.
- 12-crimp ferrule design for a reliable and secure connection between the tube and insert.
- Equipped with superior quality Santoprene seals and gaskets to prevent leaks.
2. Настройка і ўстаноўка
Before beginning installation, ensure the water supply to the fixture is turned off. Gather necessary tools such as an adjustable wrench or pliers.
- Падрыхтуйце злучэнні: Ensure the existing water supply valve and the lavatory faucet inlet are clean and free of debris.
- Падключэнне да крана: Hand-tighten the 1/2" FIP (Female Iron Pipe) end of the connector to the faucet's inlet shank. Ensure the connection is straight to avoid cross-threading.
- Connect to Supply Valve: Hand-tighten the 3/8" Comp (Compression) end of the connector to the water supply shut-off valve.
- Канчатковая зацяжка: After hand-tightening both ends, use an adjustable wrench or pliers to carefully tighten each connection an additional quarter-turn to half-turn. Не зацягвайце занадта моцна, as this can damage the seals or fittings.
- Праверце ўцечкі: Slowly turn on the water supply to the fixture. Inspect both connections for any signs of leaks. If a leak is detected, turn off the water supply and gently tighten the connection further, or re-seat the connector if necessary.
Заўвага: Always follow local plumbing codes and safety guidelines during installation.
3. Інструкцыя па эксплуатацыі
The DuraPro 102619 Lavatory Connector is a passive component designed to transport water. Once properly installed and leak-tested, its operation is integrated with the water supply system and the connected faucet or fixture. No specific operational steps are required for the connector itself beyond ensuring a secure, leak-free connection.
- Ensure water supply valves are fully open for optimal water flow.
- Regularly check connections for any signs of wear or leakage.
4. Тэхнічнае абслугоўванне
The DuraPro 102619 Lavatory Connector requires minimal maintenance. Regular inspection is recommended to ensure continued performance and prevent potential issues.
- Перыядычная праверка: Annually, or if any changes in water pressure or flow are observed, visually inspect the connector and its connections for any signs of corrosion, kinks, fraying of the braided jacket, or leaks.
- Уборка: If necessary, wipe the exterior of the connector with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners, as these can damage the stainless steel finish.
- Праверка герметычнасці: Periodically check around the connection points for any moisture or drips. Address any leaks immediately by gently tightening the connection or replacing the connector if damage is evident.
Увага: If the stainless steel braiding shows signs of degradation or fraying, replace the connector immediately to prevent potential injury from sharp strands or hose failure.
5. Выпраўленне непаладак
This section addresses common issues that may arise with the lavatory connector.
| праблема | Магчымая прычына | Рашэнне |
|---|---|---|
| Water Leak at Connection Points | Loose connection, damaged washer/gasket, cross-threaded fitting. | Turn off water supply. Gently tighten the connection an additional quarter-turn. If leak persists, disassemble, inspect washer/gasket for damage, replace if necessary, and reassemble carefully. Ensure fittings are not cross-threaded. |
| Скарачэнне патоку вады | Kinked hose, debris in the line, partially closed supply valve. | Check the hose for kinks and straighten if found. Ensure the water supply valve is fully open. If debris is suspected, turn off water, disconnect, and flush the line (consult a plumber if unsure). |
| Braided Jacket Fraying/Degrading | Wear and tear, chemical exposure, manufacturing defect. | Immediately replace the connector. Fraying can lead to hose failure and potential injury. |
6. Тэхнічныя характарыстыкі
| Асаблівасць | Дэталь |
|---|---|
| Нумар мадэлі | 102619 |
| Марка | DuraPro |
| Матэрыял | Нержавеючая сталь |
| Сувязі | 3/8" Compression x 1/2" FIP |
| Даўжыня | 20 цаляў |
| Максімальны ціск | 2400 PSI (at 70°F) |
| Вага прадмета | Прыкладна 4.32 унцыі |
| UPC | 076335102436 |
7. Інфармацыя аб гарантыі
The DuraPro 102619 Lead-Free Lavatory Connector is covered by a Гарантыя 3 год from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service. It does not cover damage resulting from improper installation, misuse, abuse, accident, or unauthorized repairs.
For warranty claims or further details, please retain your proof of purchase and contact DuraPro customer support.
8. Падтрымка кліентаў
If you have any questions regarding the installation, operation, maintenance, or troubleshooting of your DuraPro 102619 Lead-Free Lavatory Connector, please contact DuraPro customer support.
Please visit the official DuraPro website for contact information or refer to the packaging for specific support details.