Інструкцыя па эксплуатацыі эхалота глыбіні Faria 13795 Chesapeake, які праходзіць праз корпус судна

1. Уводзіны

This manual provides detailed instructions for the installation, operation, and maintenance of your Faria 13795 Chesapeake Depth Sounder Thru-Hull. This device is designed to provide accurate depth readings in various marine conditions, utilizing advanced microprocessor technology for reliable performance.

2. Інфармацыя па бяспецы

• Заўсёды адключайце харчаванне перад любой устаноўкай або тэхнічным абслугоўваннем.
• Ensure proper sealing of all thru-hull components to prevent water intrusion.
• Калі вы не ўпэўненыя ў якіх-небудзь кроках усталёўкі, звярніцеся да кваліфікаванага марскога тэхніка.
• This device is an aid to navigation and should not be used as the sole source of navigation information.

3. Змесціва ўпакоўкі

Праверце наяўнасць усіх прадметаў у камплекце:

• Faria 13795 Chesapeake Depth Sounder Display Unit
• Thru-Hull Transducer (Note: The included transducer is typically 1.5 inches. A 2-inch transducer may need to be purchased separately if required for your application.)
• Мантажнае абсталяванне
• Інструкцыя па эксплуатацыі (гэты дакумент)

4. Настройка і ўстаноўка

Proper installation is crucial for accurate depth readings. This section outlines the general steps for installing the depth sounder and its thru-hull transducer.

4.1 Кампанент заview

Малюнак 1: Faria 13795 Depth Sounder display unit (left) and the thru-hull transducer (right). The display features an LCD screen, 'ON/OFF MODE' button, and up/down arrow buttons for navigation and settings adjustment.

4.2 Устаноўка пераўтваральніка

1. Выберыце месцазнаходжанне: Choose a location on the hull that is free from turbulence, air bubbles, and obstructions. The transducer should be mounted in an area that remains submerged at all speeds.
2. Свідраваць адтуліну: Carefully drill a hole of the appropriate diameter for the transducer shaft. Refer to the transducer's specific dimensions for precise hole size.
3. Нанесці герметык: Apply a marine-grade sealant (e.g., 3M 5200) generously around the edge of the transducer flange that will contact the hull.
4. Устаўце пераўтваральнік: Insert the transducer from the outside of the hull into the drilled hole.
5. Secure Internally: From inside the boat, place the large rubber gasket around the transducer shaft, followed by the securing nut.
6. Зацягніце гайку: Hand-tighten the nut securely. Avoid over-tightening, which can damage the hull or transducer. Wipe away any excess sealant.
7. Маршрутны кабель: Route the transducer cable to the display unit, ensuring it is protected from abrasion and interference.

4.3 Display Unit Installation

1. Месца мантажу: Select a suitable location on the dashboard or panel for the display unit, ensuring clear visibility and accessibility.
2. Выразаць адтуліну: Use the provided template (if applicable) to cut the appropriate size opening for the display unit.
3. Бяспечны дысплей: Insert the display unit into the opening and secure it using the supplied mounting bracket and hardware.
4. Праводка:
   • Connect the transducer cable to the designated port on the display unit.
   • Connect the power wire (typically red) to a switched 12V DC power source.
   • Connect the ground wire (typically black) to a reliable ground point.
   • Пераканайцеся, што ўсе злучэнні надзейныя і належным чынам ізаляваны.

5. Інструкцыя па эксплуатацыі

This section details how to operate your Faria Depth Sounder.

5.1 Уключэнне/выключэнне сілкавання

• Каб уключыць прыладу, націсніце і ўтрымлівайце кнопку Рэжым уключэння / выключэння кнопку, пакуль не загарыцца дысплей.
• To power off the unit, press and hold the Рэжым уключэння / выключэння кнопку, пакуль дысплей не выключыцца.

5.2 Асноўныя аперацыі

• Upon powering on, the unit will typically display the current depth.
• The unit features automatic gain control to optimize depth readings in varying conditions.
• Падсвятленне is integrated for enhanced visibility, especially during low-light conditions.

5.3 Выбар рэжыму і налады

• Націсніце Рэжым уключэння / выключэння button briefly to cycle through different display modes or access settings menus.
• Выкарыстоўвайце Up (▲) і Уніз (▼) arrow buttons to adjust values or navigate menu options.
• Keel Offset: This setting allows you to adjust the depth reading to compensate for the distance between the transducer and the bottom of your boat's keel. Consult your boat's specifications to determine the correct offset value.
• Deep and Shallow Water Alarms: Set desired depth thresholds for both deep and shallow water. The unit will provide audio and visual alarms when these thresholds are crossed.

6. Асаблівасці

• Oversized Back-lit display for clear visibility in various lighting conditions.
• Audio and visual alarms for elevation (deep and shallow water).
• Programmable keel offset for accurate depth measurement relative to the keel.
• Automatic gain control for optimal performance across different bottom conditions.
• Depth capability: 3-199 feet (61 meters).

7. Тэхнічнае абслугоўванне

• Уборка: Працярыце дысплей мяккай губкайamp тканінай. Пазбягайце абразіўных ачышчальнікаў або растваральнікаў.
• Transducer Inspection: Periodically inspect the transducer for marine growth or damage. Clean gently with a soft brush if necessary. Ensure the transducer cable is free from kinks or damage.
• Сувязі: Check all electrical connections annually for corrosion or looseness.

8. Выпраўленне непаладак

9. Тэхнічныя характарыстыкі

• мадэль: 13795
• Марка: Фарыя
• Магчымасць глыбіні: 3-199 футаў (61 метраў)
• матэрыял: Пластыкавыя
• Вага прадмета: Прыблізна 1 фунт
• UPC: 759266137950
• Патрабаванні да магутнасці: 12V DC (typical marine electrical system)
• Дысплей: LCD з падсветкай

10. Гарантыя і падтрымка

Faria products are manufactured to high standards. For specific warranty details, please refer to the warranty card included with your product or visit the official Faria Beede Instruments website. For technical support or service inquiries, please contact Faria customer service directly.