Robertshaw 9200H Deluxe Mechanical Heat and Cool Thermostat User Manual

1. Уводзіны

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Robertshaw 9200H Deluxe Mechanical Heat and Cool Thermostat. This 24-volt thermostat is designed for single-stage heating and cooling systems, including gas, oil, electric, and heat pump systems without auxiliary heat. It features hermetically sealed contacts and a heavy-duty heat anticipator for reliable performance. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Малюнак 1: Спераду view of the Robertshaw 9200H thermostat, showing the temperature slider and system switch. Dimensions are approximately 3.6 inches (9 cm) in height.

2. Інфармацыя па бяспецы

ПАПЯРЭДЖАННЕ: Always disconnect power to the heating and cooling system at the main fuse or circuit breaker panel before installing or servicing the thermostat. Failure to do so could result in electrical shock or equipment damage.

• Пераканайцеся, што ўся праводка адпавядае мясцовым электрычным нормам і правілам.
• This thermostat is designed for 24 VAC systems only. Do not use it with line voltage systems (120V or 240V).
• Do not short out terminals on the gas valve or at the system control to test the thermostat. This can damage the thermostat and/or the system.
• Keep the thermostat clean and free from dust.

3. Ўстаноўка

3.1 Неабходныя інструменты

• Адвёртка (крыжовая і/або плоская)
• Стрыпперы/разакі для дроту
• Drill with appropriate bit (if new mounting holes are needed)

3.2 Месца мацавання

Install the thermostat on an inside wall, approximately 5 feet (1.5 meters) above the floor. Avoid locations that are:

• Near windows or doors that may cause drafts.
• Near heat sources such as lamps, radiators, or appliances.
• Пад прамымі сонечнымі прамянямі.
• Near supply registers or air ducts.
• У месцах з дрэннай цыркуляцыяй паветра.

3.3 Інструкцыі па падключэнні

1. Адключыць харчаванне: Turn off the electricity to the heating and cooling system at the main fuse or circuit breaker panel.
2. Выдаліць стары тэрмастат: Carefully remove the cover of your old thermostat. Note the wire connections to each terminal. It is recommended to label each wire with the terminal designation (e.g., R, W, Y, G) before disconnecting.
3. Усталюйце новую аснову тэрмастата: Remove the new thermostat's cover. Position the thermostat base against the wall and mark the mounting holes. Drill pilot holes if necessary, then secure the base to the wall using the provided screws.
4. Падключыце правады: Connect the wires from your system to the corresponding terminals on the Robertshaw 9200H thermostat. This thermostat is designed for 1-stagе цяпло, 1-сtage cool systems. Typical connections are:
   • R: 24V Power (often Red wire)
   • W: Heat Call (often White wire)
   • Y: Cool Call (often Yellow wire)
   • G: Fan Call (often Green wire)
   Ensure wires are securely fastened to their terminals.
5. Install Thermostat Cover: Once wiring is complete and secure, carefully snap the thermostat cover onto the base.
6. Аднавіць сілу: Turn the electricity back on at the main fuse or circuit breaker panel.

Малюнак 2: Унутраны view of the Robertshaw 9200H thermostat, illustrating the circuit board and wiring connection points. Note the terminals for R, W, Y, and G connections.

4. Аперацыя

The Robertshaw 9200H thermostat features simple mechanical controls for temperature and system mode selection.

4.1 Налада тэмпературы

• Locate the temperature slider on the front of the thermostat (refer to Figure 1).
• Slide the indicator to your desired temperature setting. The thermostat will maintain this temperature within its operating range.

4.2 Выбар рэжыму сістэмы

The system mode switch allows you to select between heating, cooling, or turning the system off.

• ЦЯПЛО: Select this mode for heating operation. The system will turn on when the room temperature falls below your set temperature.
• OFF: Select this mode to turn off both heating and cooling functions.
• ЦУД: Select this mode for cooling operation. The system will turn on when the room temperature rises above your set temperature.

4.3 Праца вентылятара

This mechanical thermostat typically operates the fan automatically with the heating or cooling call. There is no separate fan switch for continuous fan operation.

5. Тэхнічнае абслугоўванне

The Robertshaw 9200H thermostat requires minimal maintenance to ensure continued reliable operation.

• Уборка: Перыядычна працірайце тэрмастат знешняй паверхняй мяккай анучайamp тканіна. Не выкарыстоўвайце абразіўныя ачышчальнікі або растваральнікі. Сачыце за тым, каб вільгаць не трапляла ўнутраныя кампаненты.
• Паток паветра: Пераканайцеся, што вентыляцыйныя адтуліны на тэрмастаце casinне закрываюцца пылам або смеццем, бо гэта можа паўплываць на дакладнасць вымярэння тэмпературы.
• Батарэі не патрабуюцца: This mechanical thermostat does not require batteries for operation.

6. Выпраўленне непаладак

Калі ў вас узніклі праблемы з тэрмастатам, звярніцеся да наступных распаўсюджаных праблем і іх рашэнняў:

If problems persist after attempting these solutions, contact a qualified HVAC service technician.

7. Тэхнічныя характарыстыкі

• мадэль: 9200H
• тtage: 24 В пераменнага току
• Сумяшчальнасць сістэмы: Адзінкавыя-ыtage (1 Heat / 1 Cool) gas, oil, electric, or heat pump systems (without auxiliary heat)
• Тып кіравання: Mechanical, Push Button (for system mode)
• Тып дысплея: Аналаг
• Асаблівасці: Heavy Duty Heat Anticipator, Hermetically Sealed Contacts
• Памеры: Прыкладна 1.8 х 4.5 х 3.5 цалі (4.57 х 11.43 х 8.89 см)
• Вага прадмета: Прыкладна 2.72 унцый (77 грамаў)
• UPC: 662013212469

8. Гарантыя і падтрымка

For warranty information or technical support regarding your Robertshaw 9200H thermostat, please refer to the warranty card included with your product or visit the official Robertshaw website. You may also contact Robertshaw customer service directly for assistance with product inquiries, troubleshooting, or replacement parts.

вытворца: Робертшоу