Fuxtec Gasoline Water Pump FX-WP152 User Manual

Уводзіны

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Fuxtec FX-WP152 gasoline water pump. Please read this manual thoroughly before operating the device to ensure proper usage and to prevent injury or damage.

Малюнак 1: Спераду view of the Fuxtec FX-WP152 Gasoline Water Pump, showcasing its compact design and robust frame.

Інструкцыі па тэхніцы бяспекі

Заўсёды выконвайце наступныя меры бяспекі, каб знізіць рызыку траўмаў або пашкоджанняў:

• Перад эксплуатацыяй помпы прачытайце і зразумейце ўсе інструкцыі.
• Ensure adequate ventilation when operating the pump, as exhaust fumes contain carbon monoxide.
• Do not operate the pump near flammable materials or in explosive atmospheres.
• Заўсёды апранайце адпаведныя сродкі індывідуальнай абароны (СІЗ), такія як пальчаткі і ахоўныя акуляры.
• Трымайце дзяцей і навакольных далей ад працоўнай зоны.
• Never refuel the pump while the engine is running or hot.
• Ensure all connections are secure before starting the pump.

Ўстаноўка і зборка

Перад першым выкарыстаннем патрабуецца некаторая зборка і падрыхтоўка.

1. Распакаванне і праверка

Carefully remove all components from the packaging. Inspect for any signs of damage during transit. If any parts are missing or damaged, contact Fuxtec customer service immediately.

2. Attaching Hoses and Accessories

The pump comes with necessary accessories for hose connection. Ensure a tight seal to prevent air leaks, which can affect pump performance.

Figure 2: Included accessories for the water pump, showing hose connectors, clamps, and the intake filter.

1. Attach the suction hose to the inlet port (marked with an arrow pointing inwards) using the provided connector and clamp. Ensure the intake filter is securely attached to the end of the suction hose.
2. Attach the discharge hose to the outlet port (marked with an arrow pointing outwards) using the provided connector and clamp.
3. Зацягнуць усе клamps securely to prevent leaks.

3. Запраўка палівам і алеем

This pump uses a 2-stroke engine. It requires a pre-mixed gasoline and 2-stroke oil mixture. Refer to the engine manufacturer's recommendations for the correct mixing ratio, typically 1:25 or 1:50.

• Ensure the engine is off and cool before adding fuel.
• Open the fuel tank cap and carefully pour the pre-mixed fuel into the tank. Do not overfill.
• Шчыльна зачыніце вечка паліўнага бака.

Малюнак 3: бок view of the pump, highlighting the engine and the orange fuel tank.

Інструкцыя па эксплуатацыі

1. Запраўка помпы

Before starting, the pump housing must be filled with water to create a vacuum for suction.

1. Locate the priming cap on top of the pump housing.
2. Unscrew the priming cap and fill the pump housing completely with clean water.
3. Replace and securely tighten the priming cap.

Малюнак 4: View of the pump side, indicating the location of the priming cap on the pump housing.

2. Запуск рухавіка

Follow these steps to start the gasoline engine:

1. Усталюйце помпу на ўстойлівую, роўную паверхню.
2. Ensure the suction hose is submerged in the water source and the discharge hose is directed to the desired location.
3. Set the engine switch to the "ON" position.
4. Move the choke lever to the "CLOSED" (start) position for a cold engine. For a warm engine, the choke may not be necessary.
5. Pull the recoil starter handle firmly and smoothly until the engine starts. Do not pull the rope to its full extension.
6. Once the engine starts, gradually move the choke lever to the "OPEN" (run) position.
7. Дайце рухавіку прагрэцца некалькі хвілін, перш чым працаваць на поўным газе.

3. Adjusting Flow Rate

The flow rate can be adjusted by controlling the engine speed using the throttle lever. Increase engine speed for higher flow and decrease for lower flow.

4. Прыпынак рухавіка

To stop the pump, simply move the engine switch to the "OFF" position.

Тэхнічнае абслугоўванне

Regular maintenance ensures the longevity and optimal performance of your water pump.

1. Пасля кожнага выкарыстання

• Drain any remaining water from the pump housing and hoses to prevent freezing or corrosion.
• Ачысціце знешнія паверхні помпы з дапамогай рэкламыamp тканіна.
• Inspect hoses and connections for wear or damage.

2. Regular Checks (Monthly/Seasonally)

• Паветраны фільтр: Inspect and clean the air filter. Replace if heavily soiled or damaged.
• Свечка запальвання: Check the spark plug for fouling or wear. Clean or replace as needed.
• Паліўны фільтр: Inspect the fuel filter for blockages. Clean or replace if necessary.
• General Fasteners: Праверце ўсе гайкі, балты і шрубы на нацягнутасць.

3. Захоўванне

For long-term storage, prepare the pump as follows:

1. Drain all fuel from the tank and carburetor. Run the engine until it stops from lack of fuel.
2. Remove the spark plug and pour a small amount of 2-stroke oil into the cylinder. Pull the recoil starter a few times to distribute the oil, then reinstall the spark plug.
3. Store the pump in a clean, dry, and well-ventilated area, away from direct sunlight and extreme temperatures.

Ліквідацыю непаладак

This section addresses common issues you might encounter with your water pump.

Тэхнічныя характарыстыкі

Гарантыя і падтрымка

Fuxtec is committed to providing high-quality products and excellent customer service. Your Fuxtec FX-WP152 water pump is backed by our commitment to quality.

• Technical Hotline & Customer Service: For technical assistance or inquiries, please contact our dedicated customer service team.
• Наяўнасць запасных частак: Fuxtec ensures that spare parts for your product are available long-term, facilitating easy maintenance and repairs.
• Service Workshop in Germany: We operate a service workshop in Germany to provide professional support and repairs for our products.

For more information or to contact support, please visit the official Fuxtec webсайт або звярніцеся да кантактнай інфармацыі, указанай у дакументах аб куплі.