GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Уводзіны

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Інфармацыя па бяспецы

ПАПЯРЭДЖАННЕ: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Перад устаноўкай пераканайцеся, што электрычнасць адключана з дапамогай аўтаматычнага выключальніка.
• Гэта прылада прызначана для ўстаноўкі ў адпаведнасці з Нацыянальным электрычным кодэксам і мясцовымі правіламі.
• Do not use in wet locations or where directly exposed to water.
• Толькі для выкарыстання ў памяшканнях.

Змест пакета

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Ўсталявальныя шрубы
• Драцяныя гайкі (могуць адрознівацца ў залежнасці ад упакоўкі)
• Кіраўніцтва карыстальніка (гэты дакумент)

Настройка і ўстаноўка

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Зняць стары перамыкач: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Вызначыць правады:
   • Line (Hot): Usually black, coming from the circuit breaker.
   • нагрузка: Usually black, going to the light fixture or appliance.
   • Нейтральны: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Зямля: Usually green or bare copper.
4. Падключыць новы камутатар: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Падключыце лінія wire to the terminal marked "LINE".
   • Падключыце Нагрузка wire to the terminal marked "LOAD".
   • Падключыце Нейтральны wire to the terminal marked "NEUTRAL".
   • Падключыце зямля wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Перамыкач мацавання: Асцярожна ўстаўце правадны выключальнік у насценную скрынку. Замацуйце яго з дапамогай шруб, якія ўваходзяць у камплект.
6. Усталяваць насценную пліту: Attach the new or existing wall plate.
7. Аднавіць сілу: Зноў уключыце харчаванне з дапамогай аўтаматычнага выключальніка.

Малюнак 1: Спераду view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Уключэнне Z-Wave (спалучэнне)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle адзін раз. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Кіраванне камутатарам

Ручное кіраванне

• Націсніце верх of the paddle to turn the connected load ON.
• Націсніце дно of the paddle to turn the connected load ВЫКЛ.

Кантроль Z-Wave

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Тэхнічнае абслугоўванне

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Уборка: Каб ачысціць перамыкач, працярыце яго мяккай тканінайamp тканіна. Не выкарыстоўвайце абразіўныя ачышчальнікі або растваральнікі.
• Абнаўленні прашыўкі: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Агульны догляд: Ensure the switch is not exposed to excessive moisture or extreme temperatures.

Ліквідацыю непаладак

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle адзін раз. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Тэхнічныя характарыстыкі

Гарантыя і падтрымка

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webсайт або звярніцеся ў іх аддзел абслугоўвання кліентаў.

Webсайт: www.gocontrol.com

вытворца: GOCONTROL