1. Уводзіны
This manual provides essential information for the safe installation, operation, and maintenance of the Schneider Electric Acti 9 iC60 RCBO (Residual Current Circuit Breaker with Overcurrent protection), Model A9D27210. This device combines the functions of a miniature circuit breaker (MCB) and a residual current device (RCD) in a single unit, offering protection against overloads, short circuits, and earth leakage currents.
It is designed for use in electrical installations to ensure the safety of personnel and equipment. Please read this manual thoroughly before installation or use.
2. Інфармацыя па бяспецы
ПАПЯРЭДЖАННЕ: Рызыка паражэння электрычным токам або пажару.
- Installation and maintenance must be performed by qualified and authorized personnel only.
- Always disconnect power before working on the device or electrical circuit.
- Пераканайцеся, што выконваюцца ўсе мясцовыя і нацыянальныя электрычныя нормы і правілы.
- Do not use the device if it is damaged or appears to be faulty.
- The device must be correctly rated for the circuit it protects.
Невыкананне гэтых інструкцый можа прывесці да смерці, сур'ёзных траўмаў або пашкоджання абсталявання.
3. Настройка і ўстаноўка
The Acti 9 iC60 RCBO is designed for DIN rail mounting. Ensure adequate space and ventilation around the device.
3.1 Мантаж
Mount the RCBO onto a standard 35mm DIN rail. Ensure it is securely clipped into place.
Малюнак 1: бок view of the RCBO, illustrating the DIN rail mounting mechanism. The yellow clips are visible, indicating how the device attaches to a standard DIN rail.
3.2 Электраправодка
Connect the incoming and outgoing cables to the appropriate terminals. This is a 2-pole device. Refer to the wiring diagram on the device label and ensure correct polarity and torque for terminal screws.
- Уваходнае харчаванне: Connect to the top terminals (Line and Neutral).
- Выходная нагрузка: Connect to the bottom terminals (Line and Neutral).
- Ensure all connections are tight to prevent overheating and loose contacts.
Figure 2: Device label displaying the model number A9D27210 and a clear wiring diagram. This diagram indicates the correct connection points for incoming and outgoing power, as well as the internal schematic of the RCBO.
Малюнак 3: унізе view of the RCBO, highlighting the wiring terminals. These terminals are where the load-side conductors are connected after the device is mounted.
4. Інструкцыя па эксплуатацыі
The RCBO features a toggle switch for manual operation and a test button for verifying RCD functionality.
4.1 Уключэнне/выключэнне
- Каб уключыць: Push the toggle switch upwards to the "ON" (I) position.
- Каб выключыць: Push the toggle switch downwards to the "OFF" (O) position.
4.2 Тэставая функцыя
The RCBO is equipped with a test button (marked "T" or "Test") to verify the residual current protection function. This test simulates an earth fault condition.
- Працэдура: With the RCBO in the "ON" position, press the test button. The RCBO should immediately trip to the "OFF" position.
- Скід: To reset, push the toggle switch fully down to the "OFF" position, then push it up to the "ON" position.
- Частата: It is recommended to perform this test monthly to ensure proper operation of the RCD function.
Малюнак 4: Спераду view of the RCBO, clearly showing the green toggle switch for ON/OFF operation and the small test button (often labeled 'T' or 'Test') used to verify the residual current protection function.
5. Тэхнічнае абслугоўванне
The Acti 9 iC60 RCBO requires minimal maintenance. Regular testing of the RCD function is the primary maintenance task.
- Штомесячны тэст: As described in Section 4.2, press the test button monthly to ensure the RCD mechanism is functioning correctly.
- Візуальны агляд: Перыядычна правярайце прыладу на наяўнасць фізічных пашкоджанняў, змены колеру або няшчыльных злучэнняў.
- Уборка: If necessary, gently clean the exterior of the device with a dry, soft cloth. Do not use abrasive cleaners or solvents.
IMPORTANT: Do not attempt to open or repair the RCBO. Refer all servicing to qualified personnel.
6. Выпраўленне непаладак
If the RCBO trips unexpectedly or fails to operate correctly, consider the following:
| праблема | Магчымая прычына | Рашэнне |
|---|---|---|
| RCBO trips immediately upon switching on. | Persistent earth fault, short circuit, or overload in the circuit. | Disconnect all loads and try to reset. If it holds, reconnect loads one by one to identify the faulty appliance/circuit. If it still trips, consult a qualified electrician. |
| RCBO trips intermittently. | Intermittent earth fault, transient overload, or faulty appliance. | Monitor the circuit for specific events that cause tripping. Check appliances for insulation faults. Consult a qualified electrician. |
| Test button does not trip the RCBO. | Faulty RCD mechanism or incorrect wiring. | Do not use the device. It may not provide earth fault protection. Immediately consult a qualified electrician for inspection and replacement if necessary. |
| RCBO does not reset after tripping. | Persistent fault in the circuit or internal device fault. | Ensure the toggle switch is pushed fully down to the "OFF" position before attempting to reset to "ON". If it still doesn't reset, there is likely a persistent fault or the device is damaged. Consult a qualified electrician. |
If troubleshooting steps do not resolve the issue, contact a qualified electrician or Schneider Electric customer support.
7. Тэхнічныя характарыстыкі
The following specifications apply to the Schneider Electric Acti 9 iC60 RCBO, Model A9D27210:
| Асаблівасць | Каштоўнасць |
|---|---|
| Нумар мадэлі | A9D27210 |
| Марка | Кампанія Schneider Electric |
| палякі | 2P (2-Pole) |
| Намінальны ток | 10А |
| Намінальны рэшткавы працоўны ток | 30 мА |
| Тып | ASi (Type A-Si) |
| тtage | 230 вольт |
| Тып мацавання | Кранштэйн для DIN |
| Памеры прадукту (Д х Ш х У) | 7.8 х 3.6 х 8.6 см |
| Вага | 270 грамаў |
| Міжнародны код тавару (EAN/UPC) | 03606481157416 |
Figure 5: Product packaging displaying key specifications and model information for the Acti 9 iC60 RCBO.
8. Гарантыя і падтрымка
Schneider Electric products are manufactured to high standards and are typically covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Schneider Electric webсайт.
For technical support, service, or further information, please contact Schneider Electric directly:
- Webсайт: schneider-electric.com/contact
- Refer to the product packaging for regional contact details.