Okin 2 Button 5 Pin Recliner Hand Control with USB - Instruction Manual

Уводзіны

This manual provides instructions for the installation, operation, and maintenance of your Okin 2 Button 5 Pin Lift Chair or Power Recliner Hand Control with USB.

This control unit is designed for use with compatible lift chairs and power recliners, offering convenient control over reclining functions and a built-in USB charging port.

Асаблівасці прадукту

• матэрыял: Zinc alloy pane for durability.
• USB-зарадка: 5V 2A output for mobile devices.
• Даўжыня кабеля: Approximately 125cm (4.1Ft) recliner switch cable.
• Сумяшчальнасць: Works with Okin, Ashley Furniture, Dewert, Flexteel, Limoss, and many other power recliners using a 5-pin connection.

Okin 2 Button 5 Pin Recliner Hand Control with USB, showing the two control buttons and the USB charging port.

Настройка і ўстаноўка

This section details the steps for replacing or installing the hand control unit.

Неабходныя інструменты: Small flat-head screwdriver or putty knife (for prying), zip ties (optional, for cable management).

Этапы ўстаноўкі:

1. Адключыць харчаванне: Ensure the recliner is unplugged from the electrical outlet before beginning installation.
2. Выдаліць стары элемент кіравання: Carefully remove the existing hand control unit from its mounting location. This may involve gently prying it out of the armrest or side panel.
3. Адлучыце кабель: Disconnect the 5-pin connector of the old control from the recliner's motor or control box.
4. Падключыць новы элемент кіравання: Connect the new Okin 2 Button 5 Pin Hand Control's cable to the recliner's control box. Ensure the 5-pin connector is securely seated.
5. Маршрутны кабель: Route the cable neatly and secure it with zip ties if necessary to prevent snagging or damage.
6. Усталяваць блок: Insert the new hand control unit into the mounting hole. Ensure it clicks into place or is securely fastened using the provided circlips.
7. Падключыце сілкаванне: Reconnect the recliner to the electrical outlet.

Выбухнуў view diagram illustrating the components of the recliner hand control and its installation into a wooden frame, showing the switch cover, lower cover, circlips, and studs.

Close-up of the 5-pin connector, which connects the hand control to the recliner's motor system.

Інструкцыя па эксплуатацыі

The Okin 2 Button 5 Pin Hand Control provides simple operation for your power recliner.

Функцыя лежачы:

• Extend Footrest / Recline: Націсніце і ўтрымлівайце "UP" button to extend the footrest and recline the chair.
• Retract Footrest / Upright: Націсніце і ўтрымлівайце "DOWN" button to retract the footrest and return the chair to its upright position.
• Заўвага: Some recliner models may require continuous pressure on the button for the full range of motion.

Порт для зарадкі USB:

• The integrated USB port (5V 2A) is designed for charging mobile devices. Connect your device's USB cable to the port.
• Ensure the recliner is connected to a power source for the USB port to function.

Тэхнічнае абслугоўванне

To ensure the longevity and proper function of your hand control unit:

• Уборка: Keep the unit clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents, which can damage the surface or internal components.
• Праверка кабеля: Ensure cables are not pinched, twisted, or damaged. Regularly inspect the cable for any signs of wear, fraying, or cuts.
• Умовы навакольнага асяроддзя: Do not expose the unit to excessive moisture, direct sunlight, or extreme temperatures.

Ліквідацыю непаладак

Блок кіравання не адказвае:

1. Праверка харчавання: Verify that the recliner is properly plugged into a working power outlet.
2. Праверка злучэння: Ensure that all cable connections, especially the 5-pin connector to the recliner's motor, are secure and fully inserted.
3. Пашкоджанне кабеля: Inspect the control cable for any visible damage or cuts. A damaged cable may prevent proper function.
4. Motor/Power Supply: If the issue persists after checking connections and cable, the recliner's motor or power supply unit may need inspection by a qualified technician.

Порт USB не зараджаецца:

1. Recliner Power: Ensure the recliner is powered on and connected to an electrical outlet. The USB port requires power from the recliner's system.
2. Cable/Device Check: Try a different USB cable or device to rule out issues with the charging cable or the device being charged.
3. Замена блока: If the USB port still does not function, the control unit may require replacement.

Тэхнічныя характарыстыкі

Detailed dimensions of the Okin 2 Button 5 Pin Recliner Hand Control, showing measurements of 3.27 inches, 1.42 inches, and 3.9 inches.

Тыл view of the control unit, displaying product identification labels including P/N JLDK-17, DC 24V 2A, USB 5V 2A, and manufacturer Okin Refined Electric Technology Co., Ltd.

Гарантыя і падтрымка

For warranty information or technical support regarding this Okin 2 Button 5 Pin Recliner Hand Control, please refer to the documentation provided with your original recliner or contact the manufacturer directly. Specific warranty terms for this replacement part may vary.