Thincol Digital Temperature Controller (12V Model) User Manual

1. Уводзіны

This manual provides detailed instructions for the installation, operation, and maintenance of your Thincol Digital Temperature Controller (12V Model). Please read this manual thoroughly before using the device to ensure proper function and safety.

2. Інфармацыя па бяспецы

Важныя інструкцыі па бяспецы:

• Пераканайцеся, што аб'ём блока харчаванняtage matches the device's requirements (DC 12V for this model).
• Не падвяргайце прыладу ўздзеянню вады або празмернай вільготнасці.
• Avoid installing the device in areas with extreme temperatures or direct sunlight.
• Адключыце электраэнергію перад тым, як праводзіць якія-небудзь работы па падключэнні або тэхнічным абслугоўванні.
• All wiring should be performed by a qualified professional if you are unsure.
• Захоўваць у месцах, недаступных дзецям.

3. Змесціва ўпакоўкі

Пакет павінен змяшчаць наступныя рэчы:

• 1 x Thincol Digital Thermostat Temperature Alarm Controller Sensor (12V Model)

4. Прадукт скончыўсяview

Familiarize yourself with the components of your temperature controller.

Малюнак 1: Спераду view of the Thincol Digital Temperature Controller, showing the dual LED display (PV and SV), 'SET' button, up/down arrows, 'OUT' indicator, and 'Restart' button. The temperature sensor probe is connected via a black wire.

Малюнак 2: Задняя частка view of the Thincol Digital Temperature Controller, highlighting the blue screw terminals for power input and output connections.

Малюнак 3: бок view of the Thincol Digital Temperature Controller, showing its compact form factor suitable for panel mounting.

Ключавыя кампаненты:

• PV дысплей: Process Value (Current Temperature)
• Дысплей SV: Set Value (Target Temperature)
• Кнопка SET: Enters/Exits parameter setting mode.
• Кнопкі ўверх/ўніз: Adjust values in setting mode.
• Індыкатар OUT: Illuminates when the output relay is active.
• Кнопка перазапуску: Resets the device.
• Кабельныя разводкі: For power input and load output connections.
• Датчык тэмпературы: Вымярае тэмпературу навакольнага асяроддзя.

5. Тэхнічныя характарыстыкі

6. Настройка і падключэнне

Before wiring, ensure the power supply is disconnected. Incorrect wiring can damage the device or connected equipment. If you are unsure, consult a qualified electrician.

Падключэнне правадоў:

1. Спажываная магутнасць: Connect the DC 12V power supply to the designated input terminals on the back of the controller. Observe polarity (+/-) carefully.
2. Выхадная нагрузка: Connect the device you wish to control (e.g., heating element, cooling fan) to the output terminals. The controller acts as a switch for this load. Ensure the load's power requirements do not exceed the controller's maximum output (120W for the 12V model).
3. Датчык тэмпературы: Insert the temperature sensor probe into the environment where temperature measurement is required. Ensure it is securely placed and not directly exposed to heat sources or drafts that could skew readings.

Warning: Always disconnect power before making or changing any wiring connections.

7. Інструкцыя па эксплуатацыі

Setting the Target Temperature (SV):

1. Націсніце НАБОР button once. The SV (Set Value) display will begin to flash.
2. Выкарыстоўвайце Up і Уніз arrow buttons to adjust the target temperature to your desired value.
3. Націсніце НАБОР button again to confirm the setting and exit the setting mode.

Cooling/Heating Mode Selection:

The controller can operate in either cooling or heating mode. This is typically configured via an advanced parameter (often labeled P0 or P1). Please consult the full product manual for specific instructions on how to access and set the cooling or heating mode.

Advanced Parameter Settings (P3, P4, P5):

To access advanced parameters, typically a long press of the НАБОР button is required. Use the Up/Down buttons to navigate between parameters (e.g., P0, P1, P2, P3, P4, P5) and then press НАБОР again to enter the parameter's value adjustment mode.

• P3 Setting (Delay Stop/Compressor Protection): If P3 is set to '1', the thermostat will stop running for 1 minute. This function is often used for compressor delay protection in cooling systems. A long press of the НАБОР button is required to trigger this function again after it has completed its cycle.
• P4 Setting (Delayed Start): If P4 is set to '1', the thermostat will begin operation after a 1-minute delay. During this delay, the digital display will not illuminate until normal operation commences. A long press of the НАБОР button is required to trigger this function again.
• P5 Setting (Parameter Lock): By default, P5 is set to 'OFF'. Once the desired temperature and other parameters are configured, setting P5 to 'ON' will lock the data, preventing accidental changes. To modify settings again, P5 must be set back to 'OFF'.

Каліброўка тэмпературы:

The device supports temperature calibration to fine-tune accuracy. This is usually an advanced parameter (e.g., P7 or P8). Refer to the full product manual for specific instructions on how to access and adjust the temperature calibration offset.

High/Low Limit Temperature Setting:

The controller allows setting upper and lower temperature limits to prevent extreme conditions. These are typically accessible through advanced parameters. Consult the full product manual for details on setting these limits.

8. Тэхнічнае абслугоўванне

• Уборка: Працірайце прыладу мяккай сухой тканінай. Не выкарыстоўвайце абразіўныя ачышчальнікі або растваральнікі.
• Сыход за датчыкам: Ensure the temperature sensor is clean and free from debris for accurate readings.
• Праверка злучэння: Перыядычна правярайце ўсе злучэнні правадоў, каб пераканацца ў іх надзейнасці.
• захоўванне: If storing the device for an extended period, disconnect it from power and store it in a dry, cool place.

9. Выпраўленне непаладак

10. Гарантыя і падтрымка

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Thincol customer service directly. Keep your purchase receipt for warranty claims.

Manufacturer: Thincol