1. Інструкцыі па тэхніцы бяспекі
Read all instructions carefully before attempting to install this fixture. Failure to follow these instructions may result in electrical shock, fire, or other hazards.
- Усю праводку павінен выконваць кваліфікаваны электрык.
- Перад устаноўкай або абслугоўваннем адключыце сілкаванне. Гэта прыстасаванне павінна быць падключана ў адпаведнасці з Нацыянальным электратэхнічным кодэксам і дзеючымі мясцовымі кодэксамі і пастановамі.
- Для бяспекі патрабуецца належнае зазямленне.
Увага: небяспека пажару
- Ensure power is ВЫКЛ before installing or maintaining the fixture. No user-serviceable parts inside.
- Усталюйце ўбудаваны камплект і прыстасаванне ў адпаведнасці з мясцовымі нормамі.
- Do НЕ handle energized fixture when hands are wet, when standing in wet or damp паверхняў або вады.
- Do НЕ mount near flammable materials or any heat source.
- Do НЕ let power cords touch hot surfaces.
- Fixture is for indoor and dry location only.
2. Прадукт скончыўсяview
The LEDONE 2x4 FT Surface Mount Frame Kit is designed to provide a secure and aesthetically pleasing surface mounting solution for 2x4 foot LED flat panels (edge-lit and back-lit) or troffer lights. This kit allows for installation on ceilings or walls where recessed mounting is not feasible.
Image 2.1: The LEDONE 2x4 FT Surface Mount Frame Kit components.
The frame is constructed from high-quality aluminum with a white coating, offering corrosion and oxidation resistance for durability in commercial or residential environments. The assembled dimensions are approximately 48.11 x 24.31 x 2.56 inches.
Image 2.2: Detailed dimensions of the 2x4 surface mount frame kit.
3. Інструкцыя па ўстаноўцы
This section outlines the steps for installing the LEDONE 2x4 FT Surface Mount Frame Kit. Ensure all safety precautions are followed before beginning installation.
Неабходныя інструменты (не ўключаны):
- Дрыль
- Адвёртка
- Вымяральная стужка
- Аловак
Уключаныя кампаненты:
- 4 Frame pieces
- Fasteners and mounting screws
Image 3.1: Visual guide for installation steps 1 through 3.
- Збярыце каркас: Assemble the four pieces of the frame together and connect them using the provided screws. Ensure the frame forms a rigid rectangle.
- Mount the Frame: Place the assembled frame onto the desired ceiling or wall surface. Mark the screw hole locations. Drill pilot holes if necessary, then secure the frame to the surface using the provided mounting screws. Ensure the frame is level and securely fastened.
- Prepare for Panel Insertion: Carefully dismantle one of the frame pieces (typically a short side) by removing its screws. This creates an opening to slide the LED panel fixture into the frame.
Image 3.2: Visual guide for installation step 4.
- Insert LED Panel and Re-attach Frame Piece: Slide the 2x4 LED panel light into the bracket through the opening created in Step 3. Once the panel is in place, re-attach the removed frame piece and secure it with screws.
The surface mount kit is suitable for LEDONE LOC-BLPL and LOC-TROF series panels, including 1x4, 2x2, and 2x4 sizes.
Малюнак 3.3: Прыкладample of installed LED panels using the surface mount frame kits.
4. Тэхнічнае абслугоўванне
The LEDONE Surface Mount Frame Kit requires minimal maintenance. Regular inspection and cleaning will help ensure its longevity and appearance.
- Уборка: Выкарыстоўвайце мяккі, damp cloth to wipe down the frame. Avoid abrasive cleaners or solvents that could damage the white coating.
- агляд: Periodically check all mounting screws to ensure they remain tight and secure. If any screws appear loose, tighten them carefully.
- пашкоджанне: If the frame becomes bent or damaged, it may compromise the secure mounting of the LED panel. Consider replacing damaged components.
5. Выпраўленне непаладак
This section addresses common issues that may arise during or after installation.
- Frame Not Square: If the assembled frame is not perfectly square, it may be due to uneven tightening of screws or slight manufacturing variations. Ensure all screws are tightened evenly. Minor adjustments can sometimes be made by gently flexing the frame before final tightening.
- Panel Does Not Fit: Verify that the LED panel is indeed a 2x4 foot (nominal) size and compatible with surface mount kits. Ensure that one side of the frame was fully removed as per installation step 3 to allow sufficient clearance for the panel to slide in.
- Адсутнічае абсталяванне: While the kit is designed to include fasteners and mounting screws, occasionally items may be missing. Contact LEDONE customer support for replacement hardware if necessary.
- Frame Appears Flimsy After Assembly: Ensure all screws connecting the frame pieces are securely tightened. The frame is designed to be rigid once fully assembled and mounted.
6. Тэхнічныя характарыстыкі
| Асаблівасць | Спецыфікацыя |
|---|---|
| Нумар мадэлі | 2X4 SMK (Troffer & Panel) |
| Памеры прадукту (Д х Ш х У) | 48.11 х 24.31 х 2.56 цалі (прыблізна) |
| Матэрыял | Алюміній |
| Тып аздаблення | Белы |
| Тып мацавання | Паверхня |
| Вага прадмета | 5 фунта |
| Сумяшчальнасць | 2x4 ft Flat Panels (Edge-lit and Back-lit), LEDONE LOC-BLPL and LOC-TROF series |
| Атэстацыя | UL (for associated lighting fixtures, frame is a component) |
7. Гарантыя і падтрымка
LEDONE provides a 1-year limited warranty on this 2x4 inch surface mount kit. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or inquiries regarding missing components, please contact LEDONE customer service.
- вытворца: LED One Corporation
- тэлефон: (844) LEDONE6
- Факс: 1-510-217-9461
- Webсайт: www.ledoncorp.com