MEMBER'S MARK 47000 BTU Propane Patio Heater with LED Table and Wheels Instruction Manual

Уводзіны

Thank you for choosing the MEMBER'S MARK 47000 BTU Propane Patio Heater. This outdoor heater is designed to provide warmth and ambiance to your patio or outdoor living space. Featuring a powerful 47,000 BTU output, an adjustable table with LED lighting, and convenient wheels for mobility, this unit combines functionality with a sleek design. Please read this manual thoroughly before assembly, operation, or maintenance to ensure safe and efficient use of your patio heater.

Інфармацыя па бяспецы

Агульныя папярэджанні па бяспецы

• ТОЛЬКІ ДЛЯ ВЫКАРЫСТАННЯ НА ВОНКУ. Never operate this heater indoors or in an enclosed space.
• Maintain adequate clearance from combustible materials. Keep at least 3 feet (0.91 m) from sides and rear, and 2 feet (0.61 m) from the top.
• Заўсёды забяспечвайце належную вентыляцыю.
• Не захоўвайце і не выкарыстоўвайце бензін або іншыя лёгкаўзгаральныя пары і вадкасці паблізу гэтага або любога іншага прыбора.
• Perform a leak test on all gas connections before initial use and after any propane tank change.
• Keep children and pets away from the heater, especially when in operation.
• Do not move the heater while it is operating or still hot.
• Always turn off the gas supply at the propane tank when the heater is not in use.
• Ensure the heater is placed on a firm, level surface to prevent tipping. Use sand or water in the base for added stability if needed.

Змест пакета

Перад пачаткам зборкі пераканайцеся, што ўсе дэталі ёсць і не пашкоджаныя. Калі якія-небудзь дэталі адсутнічаюць або пашкоджаныя, не спрабуйце збіраць або эксплуатаваць абагравальнік. Звярніцеся па дапамогу ў службу падтрымкі кліентаў.

• База з коламі
• Апорныя кранштэйны
• Ніжні пост
• Верхні пост
• Cylinder Housing (Propane Tank Enclosure)
• Burner Assembly with Control Panel
• Reflector Panels (3 pieces)
• Рэфлекторная пласціна
• LED Tabletop
• Прапанавы шланг і рэгулятар
• Hardware (bolts, nuts, washers, wrench)

Настройка і зборка

Follow these steps carefully for proper assembly. It is recommended to have two people for certain steps, especially when handling the upper sections.

1. Прымацаваць колы да асновы: Secure the wheel assembly to the base using the provided bolts and nuts.
2. Усталюйце апорныя кранштэйны: Attach the support brackets to the base using the appropriate hardware.
3. Insert Lower Post: Secure the lower post to the support brackets.
4. Place Cylinder Housing: Slide the cylinder housing over the lower post and onto the base.
5. Assemble Reflector: Connect the three reflector panels together with the provided bolts and cap nuts. Then, attach the reflector plate to the assembled panels.
6. Attach Burner Assembly to Upper Post: Connect the burner assembly to the upper post using the washer bolts. Ensure the propane hose is routed correctly.
7. Connect Upper Post to Lower Post: Carefully insert the upper post (with burner assembly) into the lower post. Secure with bolts.
8. Attach Reflector Assembly: Mount the assembled reflector to the top of the burner assembly using the reflector studs and washers.
9. Install LED Tabletop: Place the LED tabletop onto the designated area on the main pole.
10. Secure Propane Tank: Place a standard 20 lb propane gas cylinder (sold separately) into the base. Secure it with the internal webbing strap. Connect the regulator to the propane tank valve, ensuring a tight seal.
11. Add Stability (Optional): For increased stability, especially in windy conditions, unscrew the lid at the bottom of the base and fill the base with sand or water. Tighten the lid securely.

Інструкцыя па эксплуатацыі

Connecting Propane Tank

• Ensure the propane tank valve is fully closed.
• Падключыце рэгулятар да клапана пропанавага балона. Моцна зацягніце ўручную.
• Open the propane tank valve slowly, checking for any leaks with a soapy water solution. Bubbles indicate a leak.

Запальванне абагравальніка

1. Пераканайцеся, што клапан пропан-балона цалкам адкрыты.
2. Locate the control knob and igniter button on the burner assembly.
3. Push and turn the control knob to the 'LOW' position.
4. While holding the control knob in, press the 'Igniter' button repeatedly until the burner ignites. You should hear a clicking sound and see a flame.
5. Continue to hold the control knob in for 10-15 seconds after ignition to allow the thermocouple to heat up. Release the knob. If the burner goes out, repeat steps 3-5.

Image: Control panel showing the Off, Low, High settings, and the Igniter push button.

Рэгуляванне цеплавой магутнасці

• Once lit, rotate the control knob between 'LOW' and 'HIGH' to adjust the heat intensity as desired.

Using the LED Table Light

• The LED tabletop features a separate switch, usually located underneath the table or on the main pole, to turn the light on or off.

Image: Illuminated LED tabletop, providing ambient lighting.

Выключэнне абагравальніка

• Павярніце ручку кіравання ў становішча «ВЫКЛ».
• Close the gas supply valve on the propane tank.
• Дайце абагравальніку цалкам астыць, перш чым перамяшчаць або захоўваць.

Тэхнічнае абслугоўванне

• Уборка: Regularly wipe down exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or flammable cleaning agents.
• Інспекцыі: Periodically check the gas hose and connections for any signs of wear, cuts, or leaks. Replace damaged parts immediately.
• захоўванне: When not in use for extended periods, disconnect the propane tank and store it in a well-ventilated outdoor area. Cover the heater with a weather-resistant cover to protect it from the elements.

Ліквідацыю непаладак

Тэхнічныя характарыстыкі

Гарантыя і падтрымка

For warranty information, technical support, or to order replacement parts, please refer to the documentation included with your product or contact MEMBER'S MARK customer service directly. Keep your purchase receipt for warranty claims.