HOFTRONIC Esto 2-Light GU10 Black LED Spotlight

1. Уводзіны

Thank you for choosing the HOFTRONIC Esto 2-Light GU10 Black LED Spotlight. This product is designed for indoor use, providing adjustable lighting with two GU10 LED bulbs. Constructed from high-quality aluminum, this spotlight offers a modern aesthetic and reliable performance. Please read this manual carefully before installation and use to ensure safe and optimal operation.

Image: The HOFTRONIC Esto 2-Light GU10 Black LED Spotlight installed on a ceiling, providing illumination in a modern interior setting.

2. Інструкцыі па тэхніцы бяспекі

• Always disconnect the main power supply before attempting any installation, maintenance, or bulb replacement.
• Installation should be performed by a qualified electrician to ensure compliance with local electrical codes and safety standards.
• This product is rated IP20 and is suitable for толькі для выкарыстання ў памяшканні. Do not expose to moisture or direct water.
• Забяспечыць абtage supply matches the product's requirements (230V AC).
• Не перавышайце максімальную ватtage of 35 Watts per GU10 LED bulb.
• Забяспечце дастатковую вентыляцыю вакол прыбора, каб прадухіліць перагрэў.
• Do not cover the fixture with insulating material unless specifically designed for it.

3. Змест скрынкі

Please check that all components are present and undamaged before proceeding with installation.

Image: Contents of the product box, including the spotlight fixture and mounting hardware.

• 1x HOFTRONIC Esto Double Black LED Ceiling Spot Fixture
• 1x ключ Allen
• 4x Шрубы
• 4x шайбы
• 4 штэкеры

4. Настройка і ўстаноўка

Follow these steps for safe and correct installation of your LED spotlight.

1. Падрыхтоўка да ўстаноўкі: Пераканайцеся, што асноўнае электразабеспячэнне зоны ўстаноўкі адключана аўтаматычным выключальнікам.
2. Адзначыць кропкі свідравання: Position the fixture on the ceiling at the desired location. Use the mounting holes on the base of the fixture to mark the drilling points. Refer to the diagram below for mounting dimensions.


Image: Detailed diagram of the spotlight's base with mounting hole dimensions (69mm x 69mm spacing, 4mm diameter holes, 13mm edge distance, max 12mm cable inlet).

3. Свідраваць адтуліны: Прасвідруйце адтуліны ў пазначаных месцах. Устаўце дзюбелі з камплекта ў прасвідраваныя адтуліны.
4. Падключэнне правадоў: Open the terminal cover on the fixture. Carefully connect the electrical wires from your ceiling to the terminal block inside the fixture. Ensure correct connections: Live (L), Neutral (N), and Earth (⌀). The cable inlet supports a maximum diameter of 12mm.
5. Устанавіце свяцільня: Align the fixture's mounting holes with the wall plugs. Secure the fixture to the ceiling using the provided screws and washers. Do not overtighten.
6. Insert GU10 Bulbs: Insert two GU10 LED bulbs (not included) into the lamp holders. Ensure they are securely twisted into place. Do not exceed 35 Watts per bulb.
7. Аднавіць сілу: Once installation is complete and all connections are secure, restore the main power supply.

5. Інструкцыя па эксплуатацыі

The HOFTRONIC Esto spotlight is designed for simple operation.

• Уключэнне/выключэнне харчавання: Control the spotlight using your standard wall light switch.
• Наладзіць кірунак святла: The GU10 fittings are tiltable, allowing you to adjust the light direction by up to 30 degrees. Gently pivot the inner lamp holders to direct the light as desired.

Image: Illustration of the adjustable light direction, demonstrating the 30-degree tilt capability of the GU10 fittings.

6. Тэхнічнае абслугоўванне

Regular maintenance will help prolong the life and appearance of your spotlight.

• Уборка: Ensure the power is off and the fixture is cool before cleaning. Wipe the exterior of the spotlight with a soft, dry, or slightly damp тканіна. Не выкарыстоўвайце абразіўныя ачышчальнікі, растваральнікі або агрэсіўныя хімікаты, бо яны могуць пашкодзіць пакрыццё.
• Замена лямпачкі:
  1. Адключыце сілкаванне свяцільні.
  2. Allow the bulb to cool completely if it has been recently in use.
  3. Gently push the GU10 bulb into its fitting and twist it counter-clockwise to remove.
  4. Insert a new GU10 LED bulb (max 35W) by pushing it into the fitting and twisting clockwise until secure.
  5. Аднавіць энергію.

7. Выпраўленне непаладак

If you encounter issues with your spotlight, refer to the following common problems and solutions:

• Святло не гарыць:
  • Праверце, ці ўключана асноўная крыніца харчавання.
  • Ensure the wall switch is in the 'on' position.
  • Verify that the GU10 bulbs are correctly inserted and not faulty.
  • Inspect wiring connections for looseness or damage (ensure power is off before inspection).
• Мігценне святла:
  • Ensure GU10 bulbs are fully seated in their sockets.
  • Try replacing the bulb to rule out a faulty bulb.
  • Check for loose wiring connections (with power off).
• Fixture feels hot:
  • Confirm that the installed GU10 bulbs do not exceed the maximum wattage 35 Вт.
  • Ensure there is no obstruction preventing proper heat dissipation.

Калі праблемы не знікнуць, звярніцеся ў службу падтрымкі кліентаў або да кваліфікаванага электрыка.

8. Тэхнічныя характарыстыкі

Image: Overall dimensions of the HOFTRONIC Esto 2-Light GU10 Black LED Spotlight.

9. Гарантыя

This HOFTRONIC product comes with a Гарантыя 3 год, reflecting our commitment to quality and durable construction. The robust aluminum enclosure ensures a long lifespan for your ceiling light.

Image: Warranty information, indicating a 3-year warranty and durable build quality.

10. Падтрымка

For further assistance, technical support, or warranty claims, please contact your retailer or the HOFTRONIC customer service department. Refer to your purchase documentation for contact details.