Uponor Thermal Actuator 230V NC M28 x 1.5 Instruction Manual

1. Прадукт скончыўсяview

The Uponor Thermal Actuator (Model 1022244) is designed for precise control of valves in Uponor, Polytherm, and Wirsbo Vario B underfloor heating distributors. This actuator operates on 230V AC and features a Normally Closed (NC) function, meaning the valve is closed when no power is supplied and opens when power is applied.

Асноўныя функцыі ўключаюць у сябе:

• функцыя: Normally Closed (NC) - valve closes without current.
• Намінальны выпtage: Пераменны ток 230В.
• Internal Thread: M28 x 1.5 for secure mounting.
• Індыкатар: Integrated lift indicator for visual status confirmation.
• падключэнне: Equipped with a 0.75 mm² x 1m connection cable.
• Абарона: Брызгаабароненая канструкцыя.

Figure 1: Uponor Thermal Actuator (Model 1022244). This image shows the blue housing and grey base of the actuator.

2. Інфармацыя па бяспецы

Please read all safety instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or property damage.

• Кваліфікаваны персанал: Installation and electrical connections must only be performed by qualified and authorized personnel.
• Адключэнне сілкавання: Always disconnect the main power supply before performing any installation, maintenance, or troubleshooting.
• тtage: Забяспечыць пастаўку абtage matches the actuator's nominal voltage (230 В пераменнага току).
• Асяроддзе: Do not install in environments exceeding the specified operating temperature or humidity ranges.
• Мадыфікацыі: Do not modify the actuator or its components. Unauthorized modifications void the warranty and can be hazardous.

3. Ўстаноўка і налада

This section provides instructions for the correct installation of the thermal actuator onto your underfloor heating manifold.

1. Выключэнне: Ensure the main power supply to the underfloor heating system is completely disconnected at the circuit breaker.
2. Identify Valve: Locate the specific valve on the Uponor, Polytherm, or Wirsbo Vario B underfloor heating distributor where the actuator is to be installed.
3. Мантаж прывада: Carefully screw the thermal actuator onto the valve's M28 x 1.5 internal thread. Hand-tighten until secure. Do not overtighten.
4. Электрычнае падключэнне: Connect the 230V AC electrical cable from the actuator to the appropriate control terminal on your heating system's wiring center. Ensure connections are secure and comply with local electrical codes. The actuator functions as Normally Closed (NC), meaning it will open the valve when power is supplied.
5. Verify Indicator: After connection, the lift indicator on the actuator should be visible. Its position will change once power is applied and the actuator begins to operate.
6. Аднавіць сілу: Once all connections are secure and verified, restore power to the heating system.

Figure 2: Diagram of the Uponor Thermal Actuator showing its connection cable. This illustrates the electrical connection point.

4. Аперацыя

The Uponor Thermal Actuator operates based on the electrical signal it receives from the heating control system.

• Нармальна замкнуты (НЗ): When no electrical current is supplied to the actuator, the valve remains closed, preventing water flow.
• Valve Opening: When the heating control system sends a 230V AC signal to the actuator, it begins to heat up internally. This causes a wax element to expand, slowly pushing the valve stem open. This process typically takes a few minutes.
• Valve Closing: When the electrical signal is removed, the actuator cools down, and the wax element contracts, allowing the valve to close.
• Lift Indicator: The transparent lift indicator on the side of the actuator provides a visual confirmation of the valve's status. When the valve is open, the indicator will be in a different position compared to when it is closed.

5. Тэхнічнае абслугоўванне

The Uponor Thermal Actuator is designed for long-term, maintenance-free operation. However, periodic visual inspections are recommended.

• Візуальны агляд: Periodically check the actuator for any signs of physical damage, loose connections, or leaks around the valve.
• Уборка: If necessary, gently wipe the exterior of the actuator with a dry or slightly damp тканіна. Не выкарыстоўвайце абразіўныя ачышчальнікі або растваральнікі.
• Праверка функцыянальнасці: Observe the lift indicator during heating cycles to ensure the actuator is opening and closing the valve as expected.

No internal maintenance or lubrication is required for this device.

6. Выпраўленне непаладак

If you experience issues with your Uponor Thermal Actuator, consult the following troubleshooting guide:

If troubleshooting steps do not resolve the issue, contact a qualified technician or Uponor customer support.

7. Тэхнічныя характарыстыкі

Detailed specifications for the Uponor Thermal Actuator (Model 1022244).

Figure 3: Dimensional drawing of the Uponor Thermal Actuator. This diagram provides key measurements for installation planning.

8. Гарантыя і падтрымка

For warranty information, technical support, or spare parts availability, please contact Uponor customer service or your local distributor. Keep your purchase receipt as proof of purchase.

Uponor GmbH Contact Information: