Gator Trio Hard Tri-Fold Tonneau Cover GC16019 User Manual

1. Прадукт скончыўсяview

The Gator Trio Hard Tri-Fold Tonneau Cover is designed to provide secure and weather-resistant protection for your truck bed cargo. This hard tri-fold cover features a sleek appearance and allows for vehicle operation with the cover in either an open or closed position. It arrives completely assembled for ease of installation and can be easily removed in minutes to offer full bed access when needed.

2. Сумяшчальнасць

This Gator Trio Hard Tri-Fold Tonneau Cover (Model GC16019) is specifically designed to fit:

• 2014 - 2019 Chevy/GMC Classic Silverado/Sierra 6' 7" Bed (78.9")

Ensure your truck bed length matches the specified dimensions for proper fitment.

3. Спіс дэталяў

The following components are included with your Gator Trio Hard Tri-Fold Tonneau Cover:

• Tonneau Cover Assembly
• Necessary Hardware (Clamps, Bolts, Washers, Hitch Pins)

4. Інструкцыя па ўстаноўцы

Your Gator Trio Hard Tri-Fold Tonneau Cover comes completely assembled, simplifying the installation process. No drilling is required.

4.1. Падрыхтоўка

1. Clean your truck bed rails thoroughly to ensure a secure seal.
2. Open the tonneau cover box and carefully remove the cover and all hardware components.

4.2. Rail Installation

1. Start with the driver's side rail (the rail with the trigger latch).
2. With the tailgate closed, position the side rail by equally compressing the seals on either end between the cab and the tailgate.
3. Усталюйце клamps: Position one clamp in the middle, one close to the bulkhead, and the third near the tailgate.
4. Push each clamp as high as possible on the bed rail flange.
5. Finger-tighten the clamps first to ensure the teeth engage with the grooves of the side rail.
6. Once satisfied with the placement of all three clamps, tighten the bolts with a 1/2-inch socket, holding the clamp firmly in one hand to prevent slipping or spinning.
7. Repeat these steps for the passenger side rail.

4.3. Cover Placement and Tension Adjustment

1. Position the cover on the bulkhead, allowing the bolts to slide through the pre-drilled slots.
2. Place the plastic washer and thread the nut onto the bolt. Be careful not to overtighten.
3. Cover tension is controlled by adjustable blocks. To start, place the four-position blocks with the number 4 on top and closest to the cab of the truck.
4. Secure the block with the hitch pin in the number 2 hole. This setting applies the least amount of tension to the cover.
5. Ensure both driver and passenger side blocks are in the same position.
6. Once the cover is on, it may be necessary to adjust the blocks until proper tension is achieved.

5. Інструкцыя па эксплуатацыі

5.1. Closing the Cover

1. Unhook the retainer straps if the cover was stowed open.
2. Unroll the cover towards the tailgate.
3. Firmly shut the cover, ensuring it fits into the grooves at the end of the rails.
4. Press down on the hook and loop fasteners along the length of the truck bed to secure.

5.2. Opening and Folding the Cover

1. To open the cover, pull the trigger release on the driver's side rail.
2. Roll the cover towards the cab.
3. Secure the cover by using both retainer straps. Never stow the cover against the cab without securing it. This allows complete access to your truck bed.

Важная заўвага: You can operate your vehicle with the cover opened or closed, provided it is properly secured in either position.

6. Тэхнічныя характарыстыкі

7. Інфармацыя аб гарантыі

Гэты прадукт распаўсюджваецца на a 3-гадовая гарантыя ад вытворцы. For specific terms and conditions, please refer to the warranty documentation included with your product or contact the manufacturer directly.