1. Прадукт скончыўсяview
The IBO S-150 is an electronic control unit designed for managing the circulation pump in a central heating system. Its primary function is to activate the pump when the water temperature exceeds a preset value and deactivate it when the temperature falls below that value. This intelligent control helps to optimize energy consumption and extend the operational lifespan of the pump.
Асноўныя характарыстыкі:
- Integrated Thermostat Function: Allows setting specific temperature thresholds for pump activation and deactivation.
- Функцыя супраць замярзання: Automatically activates the pump if the ambient temperature drops below 5 °C (41 °F) to prevent freezing within the system.
- энергазберажэнне: Prevents unnecessary pump operation, leading to reduced energy consumption.
- Extended Pump Lifespan: Reduces wear and tear on the pump by operating it only when required.
- Святлодыёдныя індыкатары: Two LED displays show current temperature and set stop temperature.
- Зручны інтэрфейс: Simple button controls for setting parameters.
2. Інфармацыя па бяспецы
Калі ласка, уважліва прачытайце ўсе інструкцыі па тэхніцы бяспекі перад устаноўкай і эксплуатацыяй. Невыкананне гэтых інструкцый можа прывесці да паражэння электрычным токам, пажару або сур'ёзных траўмаў.
- Электрабяспека: Installation and maintenance should only be performed by qualified personnel in accordance with local electrical codes and regulations.
- Адключэнне сілкавання: Always disconnect the power supply to the central heating system and the controller before performing any installation, wiring, or maintenance.
- Вада і вільгаць: Do not expose the controller to water, excessive moisture, or extreme temperatures. Ensure the installation location is dry and protected.
- Правільнае зазямленне: Пераканайцеся, што прылада належным чынам зазямлена, каб пазбегнуць небяспекі паражэння электрычным токам.
- Цэласнасць кабеля: Regularly inspect all cables for damage. Do not use the device if any cables are frayed or damaged.
- Прызначэнне: Use the controller only for its intended purpose as a central heating pump controller.
3. Тэхнічныя характарыстыкі
| Параметр | Каштоўнасць |
|---|---|
| Temperature Setting Range (Set Temperature) | Ад 0 °C да 99 °C (ад 32 °F да 210 °F) |
| Temperature Setting Range (Stop Temperature) | Ад 0 °C да 99 °C (ад 32 °F да 210 °F) |
| Тэмпература навакольнага асяроддзя | -10 °C да 40 °C (ад 14 °F да 104 °F) |
| Тып датчыка тэмпературы | Амічны |
| Блок харчавання Выпtage | 230 V, 50 Hz, ±10% |
| Power Consumption (Controller Only) | <5 Вт |
| Даўжыня кабеля датчыка | Прыкладна 1 м (3.3 футаў) |
| Даўжыня кабеля сілкавання | Прыкладна 1 м (3.3 футаў) |
| Pump Power Cable Length | Прыкладна 1 м (3.3 футаў) |
| Выхад | 230 В / 50 Гц |
| Maximum Load (Pump) | 6 A (Resistive Load) |
| Дакладнасць вымярэння | ~0.1 °C |
| Памеры прадукту (Д х Ш х У) | 14 х 14 х 5 см (5.5 х 5.5 х 2 цалі) |
| Вага | 370 грама (0.82 фунта) |
4. Ўстаноўка і налада
Before proceeding with installation, ensure the main power supply to your central heating system is turned off at the circuit breaker.
4.1. Мантаж кантролера
Select a suitable, dry location for mounting the controller, away from direct heat sources or excessive moisture. The controller can be mounted on a wall using appropriate fasteners (not included). Ensure sufficient space for cable connections.
4.2. Падключэнне кабеляў
The IBO S-150 controller comes with three main connections:
- Сілавы кабель: This cable supplies power to the controller. Plug it into a standard 230V, 50Hz electrical outlet.
- Pump Power Cable: This cable connects the controller to your central heating circulation pump. Ensure the pump is compatible with the controller's specifications (Max load: 6A).
- Temperature Sensor Cable: The ohmic temperature sensor should be placed in a location where it can accurately measure the water temperature of the central heating system. Typically, this is on the return pipe or a designated sensor pocket. Ensure good thermal contact for accurate readings.
Малюнак 1: Закончанаview of the IBO S-150 controller with its connected power, pump, and sensor cables.
Малюнак 2: унізе view of the controller, illustrating the connection points for the power and pump cables.
After all connections are securely made, restore power to the central heating system.
5. Аперацыя
The IBO S-150 controller features a simple interface with two LED displays and three control buttons.
Figure 3: Front panel of the IBO S-150 controller, showing the LED displays and control buttons.
5.1. Пачатковае ўключэнне
Upon initial power-on, the upper LED display will show the current temperature measured by the sensor. The lower LED display will show the currently set 'stop temperature'.
5.2. Кнопкі кіравання
- Кнопка МЕНЮ: Used to cycle through and select different settings (stop temperature, start temperature, anti-freeze function). Pressing this button allows you to enter the setting mode for each parameter.
- UP Arrow Button (▲): Used to increase the value of a selected parameter.
- DOWN Arrow Button (▼): Used to decrease the value of a selected parameter.
5.3. Setting Temperature Parameters
- Націсніце МЕНЮ button to enter the setting mode. The lower display will start flashing, indicating you can adjust the 'stop temperature'.
- Выкарыстоўвайце УВЕРХ (▲) і УНІЗ (▼) arrow buttons to set the desired temperature at which the pump should stop.
- Націсніце МЕНЮ button again to confirm the 'stop temperature' and move to the 'start temperature' setting. The lower display will flash again.
- Выкарыстоўвайце УВЕРХ (▲) і УНІЗ (▼) arrow buttons to set the desired temperature at which the pump should start. This is typically a few degrees higher than the stop temperature to prevent rapid cycling.
- Націсніце МЕНЮ button a third time to confirm the 'start temperature' and exit the setting mode. The controller will return to displaying the current and stop temperatures.
5.4. Anti-freeze Function
The anti-freeze function is automatically engaged. If the temperature measured by the sensor drops below 5 °C (41 °F), the pump will activate regardless of other settings to circulate water and prevent freezing. This function cannot be manually disabled.
6. Тэхнічнае абслугоўванне
The IBO S-150 controller requires minimal maintenance to ensure optimal performance and longevity.
- Уборка: Periodically wipe the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
- Праверка кабеля: Regularly check all connected cables (power, pump, sensor) for any signs of wear, damage, or loose connections. Replace damaged cables immediately.
- Размяшчэнне датчыка: Ensure the temperature sensor remains securely in its intended position and maintains good thermal contact with the heating system pipe.
- Умовы навакольнага асяроддзя: Verify that the controller's operating environment remains within the specified ambient temperature and humidity ranges.
7. Выпраўленне непаладак
If you encounter issues with your IBO S-150 controller, refer to the following troubleshooting guide:
| праблема | Магчымая прычына | Рашэнне |
|---|---|---|
| Кантролер не ўключаецца. | No power supply; loose power cable; faulty outlet. | Check power outlet; ensure power cable is securely plugged in; check circuit breaker. |
| Pump does not turn on when temperature is high. | Incorrect 'start temperature' setting; faulty pump connection; pump malfunction. | Verify 'start temperature' setting; check pump power cable connection; test pump independently if possible. |
| Pump does not turn off when temperature is low. | Incorrect 'stop temperature' setting; sensor malfunction. | Verify 'stop temperature' setting; check sensor connection and placement. |
| Паказанні тэмпературы недакладныя. | Sensor improperly placed; faulty sensor. | Ensure sensor has good thermal contact and is correctly positioned; replace sensor if necessary. |
| Anti-freeze function activates unexpectedly. | Ambient temperature near or below 5 °C; sensor reading error. | This is normal operation if ambient temperature is low. Check sensor reading for accuracy. |
If the problem persists after attempting these solutions, please contact a qualified technician or the product support.
8. Гарантыя і падтрымка
Каб атрымаць інфармацыю аб гарантыі і тэхнічнай падтрымцы, звярніцеся да дакументацыі, якая пастаўляецца з пакупкай, або звярніцеся да прадаўца. Захоўвайце пацвярджэнне пакупкі для любых гарантыйных прэтэнзій.
Manufacturer: IBO
Нумар мадэлі: S-150