Rx Clear 16" Inch Sand Filter User Manual

1. Уводзіны

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Rx Clear 16" Inch Sand Filter. Designed for above-ground pools, this filter system ensures crystal clear water by effectively removing debris and impurities. Please read this manual thoroughly before installation and use to ensure proper setup and longevity of your equipment.

2. Інфармацыя па бяспецы

УВАГА: Невыкананне гэтых інструкцый можа прывесці да сур'ёзных траўмаў або смерці.

• Always disconnect power to the pump before performing any service or maintenance on the filter system.
• Пераканайцеся, што ўсе электрычныя падключэнні выкананы кваліфікаваным электрыкам і адпавядаюць мясцовым нормам.
• Не выкарыстоўвайце фільтр, калі якая-небудзь дэталь пашкоджана або адсутнічае.
• Never attempt to open or service the filter while it is under pressure. Always relieve pressure before opening.
• Keep children away from pool equipment.
• Use only clean, graded filter sand as specified in this manual.
• Ensure proper ventilation when working with pool chemicals.

3. Камплектуючыя і зборка

Your Rx Clear 16" Sand Filter system includes the following main components:

• Filter Tank (16" diameter)
• Універсальная база
• 6-Position Multi-Port Valve (Top Mount)
• Манометр
• Two 6-foot Hoses
• One 3-foot Hose
• Required Clamps and Fittings

3.1. Этапы ўстаноўкі

1. Размяшчэнне фільтра: Place the universal base on a firm, level surface, preferably concrete, as close to the pool as possible. Ensure there is adequate space around the filter for maintenance and operation.
2. Assembling the Tank and Base: Carefully place the filter tank onto the universal base. Ensure it is seated securely.
   

   Image: The Rx Clear 16-inch sand filter unit, showing the tank, multi-port valve on top, and the universal base. This image illustrates the main components assembled.
3. Adding Filter Sand:
   • Remove the multi-port valve from the top of the tank.
   • Cover the standpipe opening inside the tank to prevent sand from entering it. A small cup or plastic bag can be used.
   • Carefully pour approximately 110 lbs of #20 silica sand (0.45-0.55 mm) into the filter tank. Distribute the sand evenly.
   • Remove the cover from the standpipe.
4. Installing the Multi-Port Valve:
   • Ensure the O-ring is properly seated on the valve.
   • Carefully lower the multi-port valve onto the tank, aligning the standpipe with the valve's opening. Do not force it.
   • Замацуйце клапан на баку з дапамогай прадугледжанага хомутаamp or bolts. Ensure a tight, leak-free seal.
   • Install the pressure gauge into the designated port on the valve. Не зацягвайце датчык занадта моцна.
5. Злучальныя шлангі:
   • Connect the pool pump's discharge port to the "PUMP" port on the multi-port valve using one of the 6-foot hoses and clamps.
   • Connect the "RETURN" port on the multi-port valve to the pool's return inlet using the other 6-foot hose and clamps.
   • Connect the "WASTE" port on the multi-port valve to a suitable waste line or discharge area using the 3-foot hose and clamps. Ensure the waste line directs water away from the pool area and complies with local regulations.
   • Ensure all connections are secure and leak-free. The filter is designed to accept most standard pool pumps and plumbing configurations, including 1.5-inch PVC pipes.
6. Запраўка помпы: Before starting the filter, ensure the pool pump is primed according to its manufacturer's instructions.

4. Operating the Filter System

The 6-position multi-port valve allows for various operational modes. Always turn off the pump before changing the valve position to prevent damage.

To begin normal filtration, ensure the pump is off, set the valve to ФІЛЬТРАВАЦЬ, then turn on the pump. Note the initial pressure gauge reading; this is your clean filter pressure.

5. Тэхнічнае абслугоўванне

5.1. Backwashing

Backwash your filter when the pressure gauge reads 8-10 PSI above its clean starting pressure, or when water flow to the pool noticeably decreases. This indicates that the sand bed has accumulated debris and needs cleaning.

1. Выключыце помпа басейна.
2. Rotate the multi-port valve handle to the ЗВАРОТНАЯ ПРОМЫЎКА становішча.
3. Turn on the pump and backwash for approximately 2-3 minutes, or until the water flowing out of the waste line appears clear.
4. Выключыце помпа.
5. Rotate the multi-port valve handle to the Прамыць становішча.
6. Уключыце помпу і прамыйце на працягу 30-60 секунд.
7. Выключыце помпа.
8. Rotate the multi-port valve handle back to the ФІЛЬТРАВАЦЬ становішча.
9. Уключыце помпу, каб аднавіць нармальную фільтрацыю.

5.2. Sand Replacement

Filter sand typically needs to be replaced every 3-5 years, depending on usage and water quality. Over time, sand particles can become worn and less effective at filtering. Consult a pool professional if you are unsure.

5.3. Падрыхтоўка да зімы

For colder climates, proper winterization is crucial to prevent damage to your filter system:

• Backwash and rinse the filter thoroughly.
• Зліце ўсю ваду з фільтруючага бака, адкрыўшы зліўную адтуліну ўнізе.
• Remove the multi-port valve and store it in a warm, dry place.
• Зніміце манометр.
• Store hoses in a dry place.
• Leave the drain plug open during winter to allow any remaining moisture to escape.

6. Выпраўленне непаладак

7. Тэхнічныя характарыстыкі

• Нумар мадэлі: AC166GSLB
• Дыяметр танка: 16 цаляў
• Ёмістасць пяску: Approximately 110 lbs (#20 Silica Sand)
• Памеры прадукту: 29.5 х 21.5 х 18 цалі
• Вага прадмета: 27.5 фунта
• Тып клапана: 6-Position Multi-Port (Top Mount)
• вытворца: Rx Ясна
• Краіна паходжання: ЗША

8. Гарантыя і падтрымка

For warranty information, technical support, or to order replacement parts, please contact Rx Clear customer service. Keep your purchase receipt and model number (AC166GSLB) readily available when contacting support.

For more information and products, visit the official Rx Clear store: Rx Clear Store on Amazon