WEST TUNE WTMS-380T Hotplate Magnetic Stirrer Instruction Manual

1. Уводзіны

This manual provides detailed instructions for the safe and efficient operation of your WEST TUNE WTMS-380T Hotplate Magnetic Stirrer. This device is designed for laboratory use, primarily for stirring low-viscosity liquids and solid-liquid mixtures, with integrated heating capabilities.

Асноўныя функцыі ўключаюць у сябе:

• Touchable LCD screen for convenient and accurate setting of stirring speed, heating temperature, and stirring time.
• Real-time display of set and actual values.
• Program control function with 5 memory options and 5 program control settings for automated operation.
• Upgraded aluminum hot plate (5.5 inches diameter) for fast, uniform heat transfer, durability, and corrosion resistance.
• Internal and external temperature sensors for precise temperature control of the heating plate or sampле.
• Speed range: 200-1500 rpm.
• Temperature range: RT+10-380℃/716℉.
• Timer range: 1s-99m59s.
• Maximum stirring volume: 3L.
• Ultra-temperature and over-speed alarm displays for safety.

Figure 1: WEST TUNE WTMS-380T Hotplate Magnetic Stirrer with accessories.

2. Тэхніка бяспекі

• ПАПЯРЭДЖАННЕ: Do not touch the heating plate before it cools down completely to avoid burns.
• Пераканайцеся, што прылада размешчана на ўстойлівай, роўнай паверхні.
• Always use appropriate personal protective equipment (PPE) such as gloves and eye protection when operating.
• Не выкарыстоўвайце прыладу паблізу лёгкаўзгаральных матэрыялаў.
• Забяспечце належную вентыляцыю працоўнай зоны.
• Перад чысткай або абслугоўваннем адключыце сілкаванне.
• The magnetic stirrer has ultra-temperature and over-speed alarm displays. Pay attention to these warnings.
• Выкарыстоўвайце прыладу толькі па прызначэнні, як апісана ў гэтай інструкцыі.

3. Што ў скрынцы

Пасля распакавання пераканайцеся, што ўсе кампаненты наяўныя:

• WEST TUNE WTMS-380T Hotplate Magnetic Stirrer Unit
• Сеткавы шнур
• Апорны стрыжань
• Temperature sensor (external probe)
• Magnetic stir bar
• Засцерагальнік

4. Настройка

1. Размяшчэнне: Place the stirrer on a stable, flat, and heat-resistant surface in a well-ventilated area.
2. Install Support Rod: Insert the support rod into the designated hole at the rear of the unit and tighten the securing screw.
3. Падключэнне датчыка тэмпературы: If external temperature control is desired, connect the temperature probe to the port on the rear of the unit. Secure the probe to the support rod using the provided clamp, ensuring the probe tip is immersed in the liquid to be heated/stirred without touching the bottom or sides of the beaker.
4. Падключэнне сілкавання: Connect the power cord to the unit and then to a grounded electrical outlet.
5. Першапачатковая праверка: Ensure the main power switch (located on the side/rear) is in the OFF position before connecting to power.

Figure 2: Key components and features of the stirrer.

Figure 3: Temperature probe and clamp зборка.

5. Інструкцыя па эксплуатацыі

5.1 Уключэнне/выключэнне сілкавання

Flip the main power switch (usually on the side or rear of the unit) to the "ON" position. The LCD screen will illuminate.

Figure 4: Touch LCD Screen Interface.

5.2 Setting Stirring Speed

1. On the LCD screen, touch the "Speed" display area.
2. Use the numeric keypad to enter the desired stirring speed in RPM (Revolutions Per Minute).
3. Confirm the setting. The actual speed (PV) will adjust to the set value (SV).

5.3 Setting Heating Temperature

1. Touch the "Heating plate temperature" or "Sample temperature" display area, depending on whether you are using the internal sensor or external probe.
2. Enter the desired temperature in Celsius or Fahrenheit using the numeric keypad.
3. Confirm the setting. The heating will begin, and the actual temperature (PV) will rise towards the set value (SV).

5.4 Setting Working Time

1. Touch the "Time" display area.
2. Enter the desired working duration in minutes and seconds.
3. Confirm the setting. The timer will start once the stirring and/or heating functions are activated.

5.5 Program Control Function

The device supports 5 sets of memory options and 5 sets of program control operations for automated processes.

1. Параметры памяці:
   • Touch "Memory 1" (or Memory 2-5) to access saved settings.
   • To save current settings, adjust speed, temperature, and time as desired, then long-press the desired "Memory" button until a save confirmation appears.
2. Program Control Operations:
   • Touch "Program control" to enter the program setting interface.
   • Select "Program 1" (or Program 2-5) to configure a sequence of operations.
   • For each step in the program, set parameters such as speed, temperature, and duration.
   • Save the program. The device can automatically run up to 5 sets of programs simultaneously.

Figure 5: Program and Memory Settings Interface.

5.6 Video Tutorial: Operation Overview

6. Тэхнічнае абслугоўванне

• Уборка: Заўсёды адключайце шнур харчавання ад сеткі перад чысткай. Выкарыстоўвайце мяккую губку.amp cloth with a mild detergent to clean the exterior surfaces. Do not use abrasive cleaners or solvents. Ensure no liquid enters the internal components.
• Hot Plate Care: Allow the hot plate to cool completely before cleaning. Wipe away any spills immediately.
• захоўванне: Захоўвайце прыладу ў чыстым, сухім месцы, калі яна не выкарыстоўваецца.
• Замена засцерагальніка: If the unit fails to power on, check the fuse located near the power inlet. Replace with a fuse of the same type and rating as specified in the specifications.

7. Выпраўленне непаладак

8. Тэхнічныя характарыстыкі

The following table outlines the technical specifications for the WEST TUNE WTMS-380T Hotplate Magnetic Stirrer:

Малюнак 6: Падрабязныя параметры прадукту.

9. Гарантыя і падтрымка

For warranty information, technical support, or service inquiries, please contact the WEST TUNE customer service team. Refer to your purchase documentation or the official WEST TUNE webсайт для кантактных дадзеных.

If there is any problem with the product, please contact us for satisfactory service.