Pingequa RF 2-in-1 Module with Case

Pingequa M5Stack StickC Plus NRF24 & CC1101 2-in-1 RF Module Instruction Manual

Model: RF 2-in-1 Module with Case

1. Уводзіны

This manual provides detailed instructions for the Pingequa M5Stack StickC Plus NRF24 & CC1101 2-in-1 RF Module. This dual-mode RF development board is specifically designed for the M5Stack StickC Plus, integrating both NRF24 (2.4GHz) and CC1101 (433MHz) modules. It is fully compatible with Bruce firmware, offering a plug-and-play design for both short-range and long-range wireless communication. This module is ideal for IoT, wireless control, and RF development projects.

2. Што ў скрынцы

У пакет уваходзяць наступныя кампаненты:

  • 1 x RF 2-in-1 Module (NRF24 + CC1101)
  • 1 x 2.4GHz Antenna
  • 1 x 433MHz Antenna
  • 1 x Grove Wire
  • 2 х крапежных шруб
  • 1 x 3D Printed Case
Contents of the Pingequa RF 2-in-1 Module package

Image: All components included in the package, laid out on a wooden surface. This includes the RF module, two antennas (2.4G and 433MHz), a Grove wire, two small screws, and a white 3D printed case.

Відэа распакавання

Video: An unboxing demonstration of the M5Stack StickC RF 2-in-1 Module, showing all included components and their initial presentation.

3. Настройка і ўстаноўка

Follow these steps to correctly assemble and connect your RF 2-in-1 Module to the M5Stack StickC Plus:

  1. Connect the GPIO Adapter: Carefully align and connect the 8-pin GPIO adapter of the RF module to your M5Stack StickC Plus device.
    2. Connecting the RF module to the M5Stack StickC Plus

    Image: The RF 2-in-1 module being connected to the M5Stack StickC Plus device via its GPIO pins.

  2. Plug in the Grove Cable: Connect the provided Grove cable to the designated port on the RF module. This cable facilitates communication between the module and the M5Stack StickC Plus.
  3. Secure the Module with Screws: Use the two provided mounting screws to securely fasten the RF module to the M5Stack StickC Plus. This ensures a stable connection.
  4. Install the Protective Case: Carefully place the 3D printed protective case around the assembled module and M5Stack StickC Plus. Ensure all components fit snugly within the case.
    5. Назад view of the RF module connected to M5Stack StickC Plus with case

    Выява: Спіна view of the RF 2-in-1 module attached to the M5Stack StickC Plus, showing the connection points and the protective case.

    RF module with antennas attached and protective case

    Image: The RF 2-in-1 module fully assembled with both 2.4GHz and 433MHz antennas attached, enclosed in its white protective case.

  5. Далучыце антэны: Screw the 2.4GHz antenna into the port labeled "2.4G" and the 433MHz antenna into the port labeled "433MHz" on the RF module.
    6. Збоку view of the RF module showing the antenna connections and physical switch

    Выява: Збоку view of the RF 2-in-1 module connected to the M5Stack StickC Plus, highlighting the antenna ports and the physical switch for selecting between 2.4GHz and 433MHz frequencies.

Відэа кіраўніцтва па ўстаноўцы

Video: A step-by-step guide demonstrating the installation of the RF 2-in-1 Module onto the M5StickC Plus device.

4. Інструкцыя па эксплуатацыі

The RF 2-in-1 Module supports both NRF24 (2.4GHz) and CC1101 (433MHz) communication protocols. It is designed for use with Bruce firmware.

4.1. Selecting Communication Mode

The module features a physical switch to toggle between the 2.4GHz and 433MHz modes. Locate the small switch on the RF module board.

  • Для выкарыстання CC1101 (433MHz): Toggle the physical switch to the 433MHz position. Then, navigate to the RF-CONFIG menu in your Bruce firmware and select "RF MODULE -> CC1101 (legacy)".
  • Для выкарыстання NRF24 (2.4GHz): Toggle the physical switch to the 2.4GHz position. You can then utilize the NRF24 functions within the Bruce firmware.
Топ view of the RF module showing the NRF24 and CC1101 chips and switch

Выява: Уверсе view of the RF 2-in-1 module, highlighting the NRF24 and CC1101 chips, and the physical switch for selecting between 2.4GHz and 433MHz frequencies.

4.2. Bruce Firmware Compatibility

The module is fully compatible with Bruce firmware. For advanced configuration and help, refer to the official Bruce Wiki: https://github.com/pcbY/Bruce/wiki.

Заўвага: Due to device power limits, 2.4 GHz anti-interference features, and legal regulations, the NRF24 effective range is limited. This module is designed for learning and research purposes only.

5. Выпраўленне непаладак

5.1. "CC1101 Not Found" Error

If you encounter a "CC1101 not found" or "NRF24 not found" error, this is typically caused by SPI bus timing changes and power management settings in Bruce firmware versions v1.12 and v1.13, which prevent the M5StickC Plus from detecting the module.

рашэнне: To resolve this issue, you must flash the Latest Beta Version or v1.11 from the official Bruce web flasher. The Latest Beta includes critical patches for SPI initialization and AXP2101 power management, ensuring 100% module recognition and hardware stability.

Visit the Bruce Web Flasher at: https://bruce.computer/flasher

Firmware Fix Video

Video: This video demonstrates how to fix the "CC1101 / NRF24 Not Found" error on M5StickC Plus devices running Bruce Firmware v1.13 by flashing the correct beta firmware version.

6. Тэхнічныя характарыстыкі

Памеры ўпакоўкі4.25 х 2.95 х 1.26 цалі
Вага прадмета1.44 унцыі
ВытворцаПінгеква
Нумар мадэлі таваруRF 2-in-1 Module with Case
Тэхналогія падлучэнняGPIO
Аперацыйная сістэмаFreeRTOS
Dimensions of the Pingequa RF 2-in-1 Module

Image: Technical drawing showing the dimensions of the RF 2-in-1 module: 60.8mm (2.39 inches) in length and 22mm (0.86 inches) in width.

7. Гарантыя і падтрымка

Каб атрымаць інфармацыю аб гарантыі і тэхнічнай падтрымцы, звярніцеся да афіцыйнага прадстаўніка вытворцы webсайт або звярніцеся ў службу падтрымкі кліентаў. Захоўвайце чэк аб куплі для любых гарантыйных прэтэнзій.