TWO TREES Laser Engraver Frame Upgrade Kit Instruction Manual

1. Уводзіны

This instruction manual provides detailed guidance for installing and using the TWO TREES Laser Engraver Frame Upgrade Kit. This kit is designed to expand the working area of compatible TWO TREES laser engravers, allowing for larger engraving projects. Please read this manual thoroughly before beginning installation.

Image: The TWO TREES Laser Engraver Frame Upgrade Kit, illustrating potential expanded engraving areas of 420x400mm and 600x600mm.

2. Сумяшчальнасць

This official extension upgrade kit is compatible with the following TWO TREES laser engraver models:

• ТТС-25
• ТТС-55
• ТТС-10
• TTS-55 pro
• TTS-10 pro
• TTS-20 pro

Image: Visual representation of compatible models for the upgrade kit.

3. Змесціва ўпакоўкі

Калі ласка, пераканайцеся, што ўсе пералічаныя ніжэй кампаненты ўваходзяць у камплект:

• Left and Right Frame Beams (2 pieces)
• Front and Rear Frame Beams (2 pieces)
• X-axis Beam (1 piece)
• Bellows Holder
• Toolkit (includes Allen wrenches and spanner)
• Timing Belts (2 pieces)
• Перавозка
• Wire (extension cables)
• Screw Pack (various screws)
• Кабельныя сцяжкі

Image: Layout of all components included in the upgrade kit.

4. Тэхнічныя характарыстыкі

Image: Visual comparison of the original 300x300mm engraving area versus an upgraded 420x400mm area, showing increased dimensions.

5. Настройка і ўстаноўка

Follow these steps to upgrade your laser engraver frame. For a visual guide, please refer to the tutorial video below.

5.1. Disassembly of Original Frame

1. Carefully remove the screws securing the control box to the frame. Disconnect all wires from the control board.
2. Remove the laser module from the X-axis beam by loosening its screws.
3. Loosen and remove the timing belts from the X and Y axes.
4. Disassemble the original X-axis and Y-axis frame beams from the corner brackets.
5. Remove the carriage from the X-axis beam by disassembling its wheels.

5.2. Assembly of Upgrade Kit

1. Assemble the carriage wheels: Attach the wheels to the carriage plate using the provided screws and nuts. Ensure the wheels are securely fastened.
2. Install the timing belts onto the new X-axis beam. Thread the belt through the carriage and secure it. Note: The red coupling shown in the video is for display purposes only; please refer to your actual product.
3. Attach the carriage with the installed belt to the new X-axis beam. Ensure the belt is properly tensioned.
4. Connect the new Y-axis aluminum extrusions to the existing frame corners. Use the M5*20 screws to secure these connections. Note: When installing, please make sure that the X-axis beam is parallel to the front and rear beam profiles. You can use the rectangle on the scale for auxiliary adjustment.
5. Connect the new X-axis aluminum extrusions to the Y-axis beams, forming the expanded frame. Use the M5*10 screws for these connections.
6. Re-attach the laser module to the X-axis beam.
7. Install the bellows holders and bellows onto the frame. Fix the bellows with black wire ties to ensure they are secure and manage cables effectively.
8. Connect the extension cables to the stepper motors (Y1, Y2, X) and the limit switches. Refer to the wiring diagram on the control board for correct connections. Ensure the Y2 cable is connected to the Y2 port, and the X cable to the X port.
9. Re-attach the control box to the frame using M4*20 screws.

5.3. Рэгуляванне нацяжэння

After assembly, ensure proper tension of the timing belts and smooth movement of the carriage.

• Гэта найбольш падыходнае становішча, каб адчуваць невялікае трэнне паміж колам POM і прафесіяналамfile пры кручэнні кола POM.
• Калі кола круціцца ў паветры і не падыходзіць праfile, эксцэнтрыкавую гайку можна адрэгуляваць па гадзіннікавай стрэлцы ад напрамку галоўкі шрубы з дапамогай гаечнага ключа.

Выява: Падрабязная view of the control board wiring connections, showing Y1, Y2, and X motor connections.

6. Інструкцыя па эксплуатацыі

Once the frame upgrade is complete, your laser engraver is ready for use with its expanded working area. Ensure your engraving software (e.g., LightBurn, LaserGRBL) is configured to recognize the new dimensions of your machine. Always perform a small test engraving to verify calibration and focus before starting large projects.

Малюнак: Examples of large and small projects, demonstrating the expanded capabilities of the upgraded engraver.

7. Тэхнічнае абслугоўванне

Regular maintenance ensures optimal performance and longevity of your laser engraver:

• Чысціня: Keep the aluminum profiles and wheels free from dust and debris. Use a soft cloth to wipe down surfaces.
• Нацяжэнне рамяня: Periodically check the tension of the timing belts. They should be taut but not overly tight. Adjust as needed using the eccentric nuts.
• Шчыльнасць шруб: Ensure all screws and fasteners remain tight. Loose components can affect engraving accuracy.
• Праверка кабеля: Inspect all cables for any signs of wear or damage. Ensure they are properly routed and secured with cable ties.

8. Выпраўленне непаладак

Вось некаторыя распаўсюджаныя праблемы і іх магчымыя рашэнні:

9. Карыстальніцкія парады

• Праверка сумяшчальнасці: Always confirm that your specific TTS model (e.g., TTS 20 Pro) is listed as compatible before purchasing or installing the upgrade kit.
• Крокавыя рухавікі: This kit is an extension for the frame and does not include stepper motors. You will use the existing stepper motors from your original engraver.
• Кабельнае кіраванне: Utilize the provided cable ties and corrugated tubes to keep all wiring neat and prevent interference with moving parts.

10. Гарантыя і падтрымка

For any questions regarding usage, technical support, or warranty claims, please contact TWO TREES customer service directly. Refer to the product packaging or the official TWO TREES webсайт для кантактнай інфармацыі.