1. Уводзіны
The NOYAFA NF-8209 is a versatile network cable tester designed to provide comprehensive cable testing solutions. It integrates digital and analog signaling for efficient cable tracking, along with features like cable length measurement, fault testing, Power over Ethernet (PoE) testing, hub blink, and Non-Contact Voltage (NCV) detection. This manual provides detailed instructions for safe and effective use of the device.
Figure 1: NOYAFA NF-8209 Network Cable Tester Components
2. Інфармацыя па бяспецы
- The emitter is powered by a lithium battery, and the receiver uses a 9V battery.
- Не падвяргайце прадукт ўздзеянню прамых сонечных прамянёў на працягу доўгага часу.
- Avoid using the product in dusty, humid, or high-temperature environments (above 40°C).
- Do not disassemble the product. Repairs and maintenance should only be performed by qualified professionals.
- The emitter has an automatic shutdown function. Users can set the auto-off time as needed. The receiver does not have an auto-off function.
- Remove batteries from both the emitter and receiver if the device will not be used for a long time to prevent battery leakage.
- Do not connect the device to live circuits exceeding the protection voltage (e.g., 220V mains).
- Avoid operating on communication lines during thunderstorms to prevent lightning strikes and ensure personal safety.
3. Структура і кампаненты прадукту
3.1. Emitter (Network Cable Tester)
Figure 2: Emitter Front Panel and Ports
- Дысплей: LCD screen showing test results and menu options.
- парты: CONT (Continuity), SCAN (Cable Scan), PoE (Power over Ethernet), Length/Flash (Length Measurement/Port Flash).
- кнопкі: Light (backlight), Power (on/off), Navigation (Up, Down, Left, Right), OK (confirm), C (cancel/return).
3.2. Receiver (Probe)
Figure 3: Receiver Features
- Святлодыёд харчавання: Паказвае стан харчавання.
- NCV (Бескантактавы выпtagд): Выяўляе AC voltage.
- Пераключальнік рэжымаў: Selects Analog or Digital scan mode.
- SEN (Sensitivity) Dial: Adjusts detection sensitivity.
- Power/SET Button: Уключэнне/выключэнне харчавання і выбар рэжыму.
- Раз'ём для навушнікаў: For use in noisy environments.
- Lamp: Provides illumination for dark work areas.
3.3. Remote (Wiremap)
- Порт RJ45: Used for continuity and wiremap testing in conjunction with the emitter.
Малюнак 4: Памеры вырабу
4. Інструкцыя па эксплуатацыі
4.1. Уключэнне / выключэнне харчавання
- Выпраменьвальнік: Каб уключыць/выключыць, націсніце кнопку харчавання.
- Прыёмнік: Slide the Power/SET switch to turn on/off.
4.2. Тэставанне PoE
This function automatically tests Power over Ethernet (PoE) switches. It identifies the PoE type, standard, voltage, and polarity.
- Connect one end of the network cable to the PoE port on the emitter.
- Connect the other end of the cable to the PoE switch.
- The emitter's screen will display the PoE information, including the power supply type (Endspan/Midspan/8-core), IEEE standard (802.3af/at), and voltage.
Video: Demonstration of PoE testing, continuity testing, length measurement, and cable scanning.
Figure 5: PoE Testing in progress
4.3. Continuity Testing (Wiremap)
This function tests for open circuits, short circuits, and cross-connections in STP and UTP cables.
- Connect one end of the network cable to the 'CONT' port on the emitter.
- Connect the other end of the cable to the RJ45 port on the remote unit.
- Press 'OK' on the emitter to start the test.
- The screen will display the wire sequence (R: 1-8, M: 1-8) and indicate any faults (open, short, cross) or a 'Good condition'.
Figure 6: Continuity Testing Setup
Figure 7: Possible Continuity Test Results
4.4. Length Measurement
This function measures the length of LAN cables (CAT5e, CAT6, CAT6a, STP & UTP).
- Connect one end of the network cable to the 'Length/Flash' port on the emitter.
- Ensure the other end of the cable is disconnected (open circuit).
- Navigate to the 'Length' function on the emitter and press 'OK' to start.
- The screen will display the cable length. The measurement range is 2.5m to 200m with an accuracy of ±1.6m.
Important Reminders for Length Measurement:
- The LAN cable to be tested must be de-energized.
- Disconnect the cable at the far end; no remote or other devices should be connected.
- The range must be 2.5m-120m; otherwise, it will display 0 meter.
Figure 8: Length Measurement in progress
4.5. Cable Scan (Wire Tracking)
This function helps locate LAN cables using digital, analog, or PoE modes.
- Connect the network cable to be traced to the 'SCAN' port on the emitter.
- On the emitter, select the desired scan mode (Digital, Analog, or PoE) from the main menu.
- Ensure the receiver's mode switch (Analog/Digital) matches the emitter's selected mode.
- Use the receiver to trace the cable. The signal strength will increase as you get closer to the target cable.
- Adjust the receiver's sensitivity dial for optimal performance.
Figure 9: Cable Scan Modes and Operation
4.6. Port Flash / Link Test
This function helps locate a network port by making its indicator light flash on a switch or router.
- Connect one end of the network cable to the 'Length/Flash' port on the emitter.
- Connect the other end of the cable to the target switch or router.
- Select the 'Flash' function on the emitter.
- Observe the indicator lights on the switch/router. The port connected to the emitter will flash, helping to identify it.
4.7. NCV (Безкантактны Voltagд) Функцыя
The receiver is equipped with an NCV function for accurate and safer electricity measurement.
- Slide the receiver's mode switch to NCV.
- Bring the tip of the receiver close to an AC power source or live wire. The NCV indicator light will illuminate, and an audible alarm will sound if voltagе выяўляецца.
Figure 10: NCV Induction Pen in use
4.8. Святлодыёдным асвятленне
Both the emitter and receiver feature an LED lamp to assist in working in dark environments.
- Press the Light button on the emitter to toggle the backlight.
- Націсніце Lamp button on the side of the receiver to turn its LED light on/off.
Figure 11: LED Lighting on Emitter
5. Налады
The settings menu allows customization of various parameters:
- мова: Пераключэнне паміж кітайскай і англійскай мовамі.
- Час падсвятлення: Adjust the backlight duration (15s, 30s, 60s, always on, off).
- Auto-off Time: Set the automatic shutdown time for the emitter (15min, 30min, 60min, off).
- Кантраст: Adjust the display contrast for better readability.
- Wiremap Calibration: Calibrate the wiremap function for accuracy.
- Інфармацыя пра версію: View апаратныя і праграмныя версіі.
6. Тэхнічныя характарыстыкі
| Асаблівасць | Спецыфікацыя |
|---|---|
| Дысплей | 128x64 Dot-matrix with backlight |
| Электразабеспячэнне | Літый-іённая батарэя 3.7V 950mAh |
| Максімальны рабочы ток | <150 мА |
| Папярэджанне пра нізкі зарад батарэі | так |
| Час аўтаматычнага выключэння | 15 хвіліна/30 хвіліны/60 хвілін/ВЫКЛ |
| тtagе Абарона | DC48V 5mA |
| Памеры | 130 х 70 х 28 мм |
| Cable Type (Wiremap/Length/Scan) | CAT5e, CAT6, CAT6a (STP & UTP) |
| Wiremap Test with Switch Directly | так |
| Wiremap Max Range | 600м |
| Дыяпазон выпрабаванняў даўжыні | 2.5 м ~ 200 м |
| Дакладнасць даўжыні | ±1.6м |
| Scan Max Signal Voltage | 9±1Vp-p |
| Частата сканавання | 130 кГц |
| Scan Analog/Digital Mode | так |
| Scan Max Range | 600м |
| PoE Test Range | DC 5~60V standard / non-standard PoE switch |
| PoE Voltage Дысплей | так |
| PoE PSE Type | Standard: IEEE 802.3af/at; Non-standard |
| Кампанент | Асаблівасць | Спецыфікацыя |
|---|---|---|
| Прыёмнік | Максімальны рабочы ток | <100 мА |
| Памеры | 210 х 43 х 27 мм | |
| Адчувальнасць рэгулюецца | так | |
| Пераменнага токуtage Выяўленне | так | |
| Lamp | так | |
| Тып батарэі | 9V*1pc | |
| Дыстанцыйнае | Порт Wiremap | RJ45 |
| тtagе Абарона | DC48V 5mA | |
| Памеры | 65 х 37 х 23 мм |
Figure 12: Emitter Specifications
Figure 13: Receiver and Remote Specifications
7. Тэхнічнае абслугоўванне
- Трымайце прыладу ў чысціні і без пылу і вільгаці. Выкарыстоўвайце для чысткі мяккую сухую тканіну.
- Калі прылада не выкарыстоўваецца, захоўвайце яе ў прахалодным сухім месцы.
- Replace batteries when the low battery warning appears to ensure accurate measurements.
- If the device will be stored for an extended period, remove all batteries to prevent leakage and damage.
8. Выпраўленне непаладак
| Феномен | Магчымая прычына | Рашэнне |
|---|---|---|
| Inconsistent wiremap test results for the same cable | Emitter's wiremap port or remote's RJ45 port has foreign objects. | Праверце на наяўнасць старонніх прадметаў і выдаліце іх. |
| Network cable ends are not properly inserted. | Ensure both ends of the cable are fully inserted. | |
| Emitter port is incorrectly used. | Use the correct port for the test. | |
| Cable open or out of measurement range (Length test) | Cable length exceeds 200m. | Cable is too long for measurement. |
| Cable length is less than 2.5m. | Cable is too short for measurement. | |
| No PoE test results | PoE switch is not powered. | Ensure the PoE switch is powered on. |
| Network cable is faulty. | Use continuity test to check cable integrity. | |
| Emitter port is incorrectly used. | Use the correct port for the test. | |
| Port Flash function shows no activity | Network cable is faulty. | Use continuity test to check cable integrity. |
| Switch/router is not powered. | Ensure the switch/router is powered on. | |
| Receiver does not make sound during scan | Receiver's scan mode does not match emitter's. | Ensure receiver and emitter are in the same scan mode. |
| Receiver battery is low or dead. | Заменіце батарэю прымача. | |
| Receiver sensitivity is too low. | Adjust receiver sensitivity dial to maximum. | |
| Screen display is unclear | Display contrast is not set correctly. | Adjust display contrast in settings. |
| Tester automatically shuts down after power on | Emitter battery is low. | Recharge emitter battery. |
| Length test shows "Test Failed" | Няспраўнасць прылады. | Звярніцеся ў службу тэхнічнай падтрымкі. |
| Wiremap results are out of order for a correct cable | Няспраўнасць прылады. | Звярніцеся ў службу тэхнічнай падтрымкі. |
9. Карыстальніцкія парады
- The NF-8209 can effectively detect any cable, even if it's not connected to anything, making it useful for identifying loose ends.
- The cable length measurement function is highly accurate, especially when used correctly by ensuring the cable is de-energized and disconnected at the far end.
- When using the cable scan function, ensure the receiver's mode (Digital, Analog) matches the emitter's selected mode for optimal signal detection.
- For wiremap testing over long distances (up to 200 meters), the device can still function effectively even if the emitter and remote are in different rooms, as long as both ends are connected to the cable.
- The device can show the distance to a break for each individual wire within a cable, which is very helpful for precise fault location.
10. Гарантыя і падтрымка
NOYAFA provides the following warranty and support for the NF-8209 Network Cable Tester:
- Гарантыйны тэрмін: 1-year free warranty for normal use. 3-year paid maintenance (cost of parts applies).
- Дата пачатку гарантыі: Тэрмін гарантыі пачынаецца з даты пакупкі.
- Доказ пакупкі: To claim warranty service, please present your warranty card and invoice or other valid proof of purchase. Otherwise, the warranty period will be calculated from the production date.
- Выключэнні: The warranty does not cover the product casing, user manual, packaging, batteries, and other accessories.
- Paid Repair Conditions: Repair fees will be charged under the following circumstances:
- No warranty card or valid proof of purchase, or warranty period has expired.
- Damage caused by improper operation, or failure to follow instructions for operation and maintenance.
- Damage caused by unauthorized disassembly or modification of the product.
- Natural wear and tear of components.
- Кантактная інфармацыя: For any issues or questions during use, please contact customer service at 0755-27220204 or 0755-27786545.
11. Змесціва ўпакоўкі
The standard package for the NOYAFA NF-8209 includes:
- Emitter (Network Cable Tester): 1 pc
- Receiver (Probe): 1 pc
- Remote (Wiremap): 1 pc
- Cable Adaptors: 1 set
- Carry Bag: 1 pc
- Кіраўніцтва карыстальніка: 1 шт
- Quality Certificate: 1 pc
- Charging Cable (for Emitter): 1 pc
- 9V Battery (for Receiver): 1 pc
Малюнак 14: Упакоўка і змесціва прадукту
