1. Уводзіны
This manual provides comprehensive instructions for the assembly of your TAMIYA 1/35 scale U.S. Willys MB Jeep 1/4-ton 4x4 Hobby Model Kit. Please read all instructions carefully before beginning assembly. This kit is designed for model enthusiasts and requires precision and attention to detail.

Выява 1.1: Спераду view of the TAMIYA Jeep Willys MB 1/4-ton 4x4 Model Kit box.
2. Інфармацыя па бяспецы
WARNING: Contains small parts that could be a choking hazard. Not suitable for children under 3 years.
- Always use tools with care. Sharp tools such as hobby knives and side cutters can cause injury if not handled properly.
- Model cement and paints should be used in a well-ventilated area. Avoid inhaling fumes.
- Keep all parts and tools out of reach of small children and pets.
- Dispose of waste materials responsibly.
3. Змесціва ўпакоўкі
Your TAMIYA Jeep Willys MB 1/4-ton 4x4 Hobby Model Kit includes the following components:
- Plastic sprues with all necessary parts for the Jeep assembly.
- Clear parts for windshields and headlights.
- Driver figure in a relaxed sitting pose.
- Decal sheet with markings for five different vehicles.
- Буклет з інструкцыяй.

Выява 3.1: Канецview of the kit contents inside the box.

Малюнак 3.2: Падрабязны view of the plastic sprue parts included in the kit.
4. Неабходныя інструменты
The following tools are recommended for assembling your model kit:
- Angled Tweezers
- Cutter-Knife
- Decal-Scissors
- Бакавы разцы
- Paint Brush Set
- Masking Tape (10mm with dispenser)
- Plastic Cement (e.g., Tamiya Plastic Cement)
- Decal Adhesive Soft/Haftmittel

Image 4.1: A selection of recommended tools for model assembly.
5. Інструкцыя па зборцы
Follow the step-by-step diagrams in the included instruction booklet. General steps include:
- Carefully cut parts from the sprues using a side cutter.
- Clean any excess plastic (flash) from the parts with a hobby knife or sandpaper.
- Assemble sub-assemblies (e.g., engine, chassis, interior) as indicated.
- Use plastic cement sparingly to join parts. Allow sufficient drying time.
- Attach larger components to form the main structure of the Jeep.
- Install clear parts for windshields and headlights.
- Assemble and position the driver figure as desired.
Відэа 5.1: Прадукт скончаныview Video. This video provides a general look at the TAMIYA Jeep Willys model kit and its components, offering a visual introduction to the product before assembly.
6. Фарбаванне і нанясенне налепак
Refer to the included painting guide for recommended colors and placement. TAMIYA offers a range of acrylic and spray paints suitable for this model.
- Apply paint in thin, even coats. Allow each coat to dry thoroughly before applying the next.
- Use masking tape to protect areas not intended for painting.
- Cut decals carefully from the sheet. Dip them in water for a few seconds until they can slide off the backing paper.
- Position decals on the model and gently press out any air bubbles or excess water. Use decal setting solutions for better adhesion and a painted-on look.

Малюнак 6.1: Прыкладample of a paint guide showing recommended TAMIYA paint colors for the model.
7. Displaying Your Model
Once assembled and painted, your TAMIYA Jeep Willys MB is ready for display. Consider placing it in a dust-free environment to preserve its finish. A display case can protect the model from dust and accidental damage.
8. Клопат і дэманстрацыя
To maintain the appearance of your model:
- Рэгулярна працірайце пыл мяккай шчоткай або сціснутым паветрам.
- Avoid direct sunlight, which can fade paint and decals over time.
- Keep the model away from extreme temperature changes or high humidity.
9. Common Assembly Tips
- Always dry-fit parts before applying cement to ensure a proper fit.
- Use a small amount of cement to avoid damaging plastic surfaces.
- For small parts, use tweezers for precise placement.
- If a part does not fit easily, check for excess plastic or misalignment before forcing it.
10. Тэхнічныя характарыстыкі
| Асаблівасць | Дэталь |
|---|---|
| Марка | ТАМІЯ |
| Назва мадэлі | JEEP WILLYS 1/4 TON 4X4 |
| Маштаб | 1/35 |
| Тып матэрыялу | Пластыкавыя |
| Колькасць частак | 99 |
| Памеры прадмета (Д х Ш х У) | 10.25 х 6.25 х 1.5 цалі |
| Вага прадмета | 0.1 кілаграма |
| Уключаныя кампаненты | Model Kit, Decals and Markings |
11. Гарантыя і падтрымка
This product is sold without an explicit warranty. For any questions regarding assembly or missing parts, please contact the manufacturer, MMD Holdings, or refer to the official TAMIYA webсайт для рэсурсаў падтрымкі.





