вул. М5СТЭКamp-S3Bat Embedded Core Module User Guide

вул. М5СТЭКamp-S3Bat Embedded Core Module

Апісанне

Stamp-S3Bat is an embedded core module integrated with power management. It utilizes the ESP32-S3-PICO-1-N8R8 as the main control core, supports 2.4GHz Wi-Fi, and comes with built-in 8MB Flash and 8MB PSRAM.
It provides 11 GPIO pins, an onboard battery power interface, and can be directly connected to an external 3.7V lithium battery for power supply.

With an efficient built-in PMIC and multi-level power control design, it supports power input and output control, as well as status monitoring for input voltagе і акумулятар абtage. It supports external low-power wake-up. After the main controller shuts down and enters low-power sleep mode, it can be triggered to wake up via an external PMIC wake-up IO. The module features an onboard user button and a programmable RGB LED. With 2.54mm standard-pitch half-hole solder pads, it can be integrated into your applications through SMT, DIP, or other methods, helping developers quickly build IoT applications.

Тэхнічныя характарыстыкі

Хуткі старт

Падрыхтоўка

1. Наведайце афіцыйны сайт Arduino webсайт і ўсталюйце IDE Arduino
   https://www.arduino.cc/en/Main/Software
2. Дадаць наступнага кіраўніка савета дырэктараў URL каб File → Налады → Менеджар дадатковых дошак URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Адкрыйце дыспетчар плат, знайдзіце «ESP32» і націсніце «Усталяваць».
4. After installation, select the board “ESP32S3 Dev Module”.
5. Configure the following options. USB CDC On Boot: “Enabled”, PSRAM： “OPI PSRAM”, USB Mode: “Hardware CDC and JTAG«

Сканаванне Wi-Fi

• Выберыце былampпраграма «Ex»amples” → “WiFi” → “WiFiScan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
• After uploading is complete, open the Serial Monitor to view Інфармацыя аб сканаванні Wi-Fi.

Сканаванне BLE

• Выберыце былampпраграма «Ex»amples” → “BLE” → ”Scan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
• After uploading is complete, open the Serial Monitor to view Інфармацыя пра BLE-сканаванне.

Папярэджанне FCC

Засцярога FCC:
Любыя змены або мадыфікацыі, не адобраныя бокам, адказным за адпаведнасць, могуць ануляваць права карыстальніка на эксплуатацыю абсталявання.

Гэта прылада адпавядае частцы 15 Правілаў FCC. Аперацыя залежыць ад наступных двух умоў:

1. This device may not cause harmful interference, andThiss device must accept any interference received, including interference that may cause undesired operation.

ВАЖНАЯ ЗАЎВАГА:

Заўвага: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use,s and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Пераарыентуйце або перамесціце прыёмную антэну.
• Павялічце адлегласць паміж абсталяваннем і прымачом.
• Падключыце абсталяванне да іншай разеткі, чым тая, да якой падключаны прыёмнік.
• Звярніцеся па дапамогу да дылера або дасведчанага радыё/тэлетэхніка.

Заява FCC аб уздзеянні радыяцыі:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated wita h minimum distance of 20cm between the radiator & your body.

Часта задаюць пытанні